 | | BricxCC & fast firmware download —John Hansen
|
| | | I've had a report that fast firmware downloading doesn't work with the latest release of BricxCC (either tower). In my tests, with an RCX 1.0 brick plugged in, low ambient light, short distances from the USB tower, and all the firmwares I have (...) (21 years ago, 3-Nov-03, to lugnet.robotics.rcx)
|
| | | |
| | | | | RE: BricxCC & fast firmware download —Ralph Hempel
|
| | | | | John, I have yet to get fast or slow downloading to work with BricxCC on my RCX 1.0 with either the USB or serial tower... Ralph (...) (21 years ago, 3-Nov-03, to lugnet.robotics.rcx)
|
| | | | | |
| | | | | | | Re: BricxCC & fast firmware download —John Hansen
|
| | | | | | (...) Yikes! Do other forms of tower communication seem to work fine from within BricxCC? Does NQC download firmware in either fast or slow mode with your USB or serial towers? What errors, if any, are reported (and when do they appear - right away (...) (21 years ago, 3-Nov-03, to lugnet.robotics.rcx)
|
| | | | | | |
| | | | | | | | Re: BricxCC & fast firmware download —John Hansen
|
| | | | | | (...) I meant also to ask whether this is a new situation, i.e., whether BricxCC used to work but now it is broken or whether you have never had success with BricxCC. Thanks, John Hansen (21 years ago, 3-Nov-03, to lugnet.robotics.rcx)
|
| | | | | | |
| | | | | Re: BricxCC & fast firmware download —Philippe Hurbain
|
| | | | | Hello John, Worked fine for me, with the following setup: RCX2.0, USB tower, BricxCC 3.3.7.6, firm0328.lgo, Win2000. Distance between tower and brick: 20 cm. Download time: 1'25" I tried also 50 cm away (worked) and 1 m away (failed). Philo (21 years ago, 3-Nov-03, to lugnet.robotics.rcx)
|
| | | | | |
| | | | | Re: BricxCC & fast firmware download —Travis Kunce
|
| | | | "John Hansen" <JohnBinder@aol.com> wrote in message news:Hns82p.1ItF@lugnet.com... (...) latest (...) plugged (...) firmwares (...) attempts (...) but in (...) it (...) BricxCC? (...) 2.0 (...) I have never been able to get bricxCC to properly (...) (21 years ago, 4-Nov-03, to lugnet.robotics.rcx)
|
| | | | |
| | | | | | Re: BricxCC & fast firmware download —John Hansen
|
| | | | | (...) Have you ever tried using NQC to download the firmware? If so, does it work? Using RcxCC to download your firmware means you are stuck in the serial tower world and slow firmware downloading. Have you tried both slow and fast mode firmware (...) (21 years ago, 4-Nov-03, to lugnet.robotics.rcx)
|
| | | | | |
| | | | | | Re: BricxCC & fast firmware download —Mario Ferrari
|
| | | | (...) Same for me. I'm using serial tower and 1.0, 1.5 and 2.0 RCXs. Downloading from NQC works fine in both modes. Mario (21 years ago, 4-Nov-03, to lugnet.robotics.rcx)
|
| | | | |
| | | | | | Re: BricxCC & fast firmware download —John Hansen
|
| | | | (...) Slow mode with the serial tower definitely was broken in BricxCC for a really long time because nobody ever reported to me that it was broken until about 2 or 3 weeks ago. I apologize for not noticing this problem on my own. Unfortunately, it (...) (21 years ago, 4-Nov-03, to lugnet.robotics.rcx)
|
| | | | |
