 | | Re: light sensor multiplexer —Michael Gasperi
|
| | | "Nitin Patil" <gn1721@lycos.com> wrote in message news:GAKC9v.F5A@lugnet.com... (...) With the 0.1uF in parallel with the 4.7K, the voltage on the clock circuit is still above the measurement voltage during the normal read interval. It doesn't (...) (23 years ago, 21-Mar-01, to lugnet.robotics.rcx)
|
| | | |
| | | | | Re: light sensor multiplexer —Nitin Patil
|
| | | | In lugnet.robotics.rcx, Michael Gasperi writes: Ok I agree what you say about time constant of your RC But still by using such low resistance you are wasting power. almost 1.5 mA is flowing through this 4.7K. you can keep RC constant and increase R (...) (23 years ago, 22-Mar-01, to lugnet.robotics.rcx)
|
| | | | |
| | | | | | Re: light sensor multiplexer —Michael Gasperi
|
| | | | | "Nitin Patil" <gn1721@lycos.com> wrote in message news:GALoKA.Eto@lugnet.com... (...) mA (...) If you use my simple approach, you need 4.7k and around 0.1uF. You need a low enough resistance to guarantee that the voltage drops to CMOS logic level 0 (...) (23 years ago, 22-Mar-01, to lugnet.robotics.rcx)
|
| | | | | |
| | | | | | Re: light sensor multiplexer —Stef Mientki
|
| | | | hi Nitin, I'm an energy freak to, but I can't follow your reasoning Because I'm building a multiplexer too (probably will be posted next week, so I can make still some changes) and I'm using even lower resistor values then Michael (due to a (...) (23 years ago, 22-Mar-01, to lugnet.robotics.rcx)
|
| | | | |
| | | | | | Re: light sensor multiplexer —Nitin Patil
|
| | | | Hi Stef, sorry for little late. What I am doing is that I need to get the voltahge down and most efficient way of doing that without losing swing ( if you divide you lose swing too) is level shift it and you can do it by putting by Zener. I need (...) (23 years ago, 27-Mar-01, to lugnet.robotics.rcx)
|
| | | | |
| | | | | | Re: light sensor multiplexer —Stef Mientki
|
| | | | Hi Nitin, thanks for your information. You know, by asking questions, you'll get the answers often from yourself. Just when I posted the question to you, Eureka. But let's be fair, you were the one who triggered me. I've adapted (without the power (...) (23 years ago, 27-Mar-01, to lugnet.robotics.rcx)
|
| | | | |
| | | | | | Re: light sensor multiplexer —Nitin Patil
|
| | | | Hello to every one.... all the time I was promising to put up ckt Digram for time being I have included hand drawn Ckt visit (URL) I am using are low thereshold FETs (...) (23 years ago, 30-Mar-01, to lugnet.robotics.rcx)
|
| | | | |
| | | | | | Re: light sensor multiplexer —Stef Mientki
|
| | | | hi Nitil, that's a nice and simple cirquit, but isn't there anything wrong with the grouding ? (...) -- met vriendelijke groet, Stef Mientki email: s.mientki@ids.kun.nl tel: 024 361 3905 fax: 024 354 1211 Postadres: KUN / fmw 171 Instrumentele (...) (23 years ago, 31-Mar-01, to lugnet.robotics.rcx)
|
| | | | |
