 | | How to stop, after running program (Ultimate RoboLab)
|
|
I have loaded a sample program. After the program is finished the logo "LEGO" is on the RCX. How to stop this, because I can't load a new program? Now a take out the battery's! Thanks to the makers of the Ultimate RoboLab, it is a great program !!!! (...) (18 years ago, 31-Aug-06, to lugnet.robotics.rcx.robolab)
|
| |
| | Re: Ultimate Robolab
|
|
I'm glad to finally announce that ULTIMATE ROBOLAB now has its own web-site : (URL) which UR150 can be downloaded freely. Follow the install instruction from the web-site (getting started) Requirements : ROBOLAB254 must be running on your PC or MAC. (...) (18 years ago, 24-Aug-06, to lugnet.robotics.rcx.robolab)
|
| |
| | Ultimate Robolab
|
|
Where can I get (buy) the "Ultimate Robolab"? "Ultimate ROBOLAB v.150 now available soon", when and where? Jan Kromhout Hellevoetsluis-NL (18 years ago, 24-Aug-06, to lugnet.robotics.rcx.robolab)
|
| |
| | Original Communications Protocol Documentation
|
|
Hello, I have just finished writing up my little project to discover the protocol for talking to/from the RCX. The finished document as a PDF is at: (URL) I wrote this up to facilitate communications to a PC from an RCX or Spybot with the standard (...) (18 years ago, 23-Aug-06, to lugnet.robotics.rcx, FTX)
|
| |
| | Re: Watching Arrays
|
|
(...) Thanks John! I never knew about that F12 thing :) -Rob A> (18 years ago, 17-Aug-06, to lugnet.robotics.rcx.nqc)
|
| |
| | Re: Watching Arrays
|
|
(...) The way to do this is to find out the variable number assigned by NQC to your array variable and then watch that variable number plus all the ones up through the size of your array. You can find out the variable number by viewing the code (...) (18 years ago, 17-Aug-06, to lugnet.robotics.rcx.nqc)
|
| |
| | Watching Arrays
|
|
I have a program (RCX2 target) that uses a couple of global arrays. I am using BricxCC 3.3 How can I view the contents of the array at run time? "Watch the Brick" shows me Var0 to Var 31 but these don't seem to relate/contain the values I initially (...) (18 years ago, 17-Aug-06, to lugnet.robotics.rcx.nqc)
|
| |
| | Re: swan firmware motor problem
|
|
(...) I have tried it, but it did not make a difference. The motors still won't run. I must admit that I did not think of it before because I thought (maybe wrongly) that the old API would stay the same and that you would have to use the new (...) (18 years ago, 11-Aug-06, to lugnet.robotics.rcx.nqc)
|
| |
| | RE: swan firmware motor problem
|
|
I will post latest firmware on web site soon. -----Original Message----- From: news-gateway@lugnet.com [mailto:news-gateway...ugnet.com] On Behalf Of Gustavo Brinck Sent: Thursday, August 10, 2006 7:27 PM To: lugnet.robotics.rcx....lugnet.com (...) (18 years ago, 11-Aug-06, to lugnet.robotics.rcx.nqc)
|
| |
| | Re: swan firmware motor problem
|
|
(...) I don't have the new firmware, but maybe you can try: #define NORMAL_SPEED 100 because, now the firmware have 100 step of motor pwr control. Best Regards Gustavo (18 years ago, 11-Aug-06, to lugnet.robotics.rcx.nqc)
|
