| | Re: error in using brickOS under Bricx Command Center
|
|
(...) Can you do F12 and post the contents (if any)? Do you have bash installed? While the error message is displayed you can open a command prompt and change directory to the location of your source code file. There you should find a .cmd and a (...) (19 years ago, 29-Sep-05, to lugnet.robotics.rcx.legos)
|
|
| | Re: Latest version BrixCC
|
|
(...) I have not yet made an official 3.3.7.9 release of BricxCC. My apologies for the delay. For now you can use the latest version in swan_test.zip. John Hansen (19 years ago, 29-Sep-05, to lugnet.robotics.rcx.nqc)
|
|
| | Re: Can't upload new program after I have used LNP under brickos
|
|
(...) Well, thanks for the help, that didn't actually work. But I found it out, what was my fault. In my Program I changed the LNP Base adress of the robot. After that the robot did not react to the default adress 0. So, at the end of the program I (...) (19 years ago, 29-Sep-05, to lugnet.robotics.rcx.legos)
|
|
| | Latest version BrixCC
|
|
Hi, I found on the sourceforge.net the Brixcc version 3.3.7.7 and in the swan_test.zip the version 3.3.7.9. Is there a newer version? Regards, Jan Kromhout Hellevoetsluis-NL (19 years ago, 27-Sep-05, to lugnet.robotics.rcx.nqc)
|
|
| | Enchanced Firmware
|
|
Hi, Can someone tell me wath the status is of the Enhanced Firmware? and the latest version of BrixCC? Regards Jan Kromhout Hellevoetsluis-NL (19 years ago, 27-Sep-05, to lugnet.robotics.rcx)
|
|
| | Re: data recording in BrickOS ?
|
|
Am Mon, 26 Sep 2005 12:35:05 GMT "Francois Bardet" <f.bardet@voila.fr> tippte: (...) this is not the default i programmed this functions, but the docu is in only in german avialible if you can read german, have a look at (URL) there was an other (...) (19 years ago, 26-Sep-05, to lugnet.robotics.rcx)
|
|
| | Re: Can't upload new program after I have used LNP under brickos
|
|
(...) You had to turn on the lnp, with something like this: (I forget the exact commands) lr_startup(); lr_init(); lnp_init(); Make sure you turn it off: lr_shutdown(); Steve (19 years ago, 26-Sep-05, to lugnet.robotics.rcx.legos)
|
|
| | data recording in BrickOS ?
|
|
Hi Mindstormers, 1) Does BrickOS allow to write/read measured data into the RCX memory, in order to plot or process it later on the computer ? If yes, what are the command lines to : - allocate the memory space ? - to write and read ? - free this (...) (19 years ago, 26-Sep-05, to lugnet.robotics.rcx)
|
|
| | Can't upload new program after I have used LNP under brickos
|
|
Hello, |I have the following problem: |when I use lnp under brickos, the rcx does no longer respond to the legotower. |This means that I can't delete the program nor overwrite it. | |Pershaps somebody can help. | |Thanks, | |Andy (19 years ago, 26-Sep-05, to lugnet.robotics.rcx.legos)
|
|
| | Unable to delete programm after having used lnp under brickos
|
|
Hello, I have the following problem: when I use lnp under brickos, the rcx does no longer respond to the legotower. This means that I can't delete the program nor overwrite it. Pershaps somebody can help. Thanky, Andy (19 years ago, 26-Sep-05, to lugnet.robotics.rcx)
|