 | | sys_time not working
|
|
Hi i install successfully brickOS-0.2.6.10 under Win2000 without any problems and ran successfully "helloworld.lx" I created one first elementary small program using the sys_time function. The problem is that it doesn't compile correctly. The (...) (21 years ago, 5-Aug-03, to lugnet.robotics.rcx.legos)
|
| |
| | Re: BrickOS installation with WinME and Cygnus problems
|
|
[SNIP] (...) [SNIP] Tom, I would follow Max's advice about posting your commands and output here. But one thing that might cause issues with your setup is your path. It looks like the windows dos commands (C:\WINDOWS\COMMAND) come before your cygwin (...) (21 years ago, 5-Aug-03, to lugnet.robotics.rcx.legos)
|
| |
| | Re: BrickOS installation with WinME and Cygnus problems
|
|
(...) I would not try to follow both of these instructions. Pick one and do just exactly what that set of instructions says to do. My favorite, naturally, is the second set (since getting the right set of GCC source code and compiling it without (...) (21 years ago, 5-Aug-03, to lugnet.robotics.rcx.legos)
|
| |
| | Re: BrickOS installation with WinME and Cygnus problems
|
|
(...) PATH=C:\WINDOWS;C:\W...IN\H8300-0 00821\H-I686-CYGWIN32\BIN; (...) OK, the best way to get help is: * Start with the *first* problem which occurs. Problem #3 is very likely the cause of #1 and #2. * Show *exactly* the commands you typed and (...) (21 years ago, 5-Aug-03, to lugnet.robotics.rcx.legos)
|
| |
| | BrickOS installation with WinME and Cygnus problems
|
|
Hello, I have spent several hours trying to install BrickOS on my Windows ME system. I am a novice with C/Cygwin/linux, so have been diligently searching the Lugnet posts for clues. That has gotten me a little farther each day, but now I am _really_ (...) (21 years ago, 5-Aug-03, to lugnet.robotics.rcx.legos)
|
| |
| | Announcing Full Throttle - Control LDCC From Windows
|
|
I have just released (URL) version 1.00> of a program that I call Full Throttle. This Windows application uses your Mindstorms IR tower (either serial or USB) to communicate with an RCX that is running (URL) Mark Riley's LDCC replacement firmware> (...) (21 years ago, 4-Aug-03, to lugnet.trains, lugnet.robotics.rcx, FTX) !!
|
| |
| | Re: Problems with BrickOS installation
|
|
(...) I would recommend using the pre-built Hitachi tools which are still available from my BricxCC website. (URL) simpler than trying to download all the right versions of the GCC source code. John Hansen (21 years ago, 4-Aug-03, to lugnet.robotics.rcx.legos)
|
| |
| | Problems with BrickOS installation
|
|
Hi, I'm following these directions explicitly: (URL) installed just fine. When I run buildgcc.sh it dies trying to assemble libgcc1.S. The comments at the top of the file cause syntax errors. The comments are dilineated with ";;". How can the (...) (21 years ago, 3-Aug-03, to lugnet.robotics.rcx.legos)
|
| |
| | Re: Robolab upgrade to 2.5.3 and other things
|
|
(...) Unfortunately the Service Pack 1 does not seem to work properly to upgrade from 2.5 to 2.5.2. The best way is to get a copy of the current Robolab ver 2.5.2 which is called "ROBOLAB with Training Missions" from your local LEGO distributor. (...) (21 years ago, 3-Aug-03, to lugnet.robotics, lugnet.edu, lugnet.robotics.rcx.robolab, lugnet.robotics.edu)
|
| |
| | Re: light sensor question
|
|
(...) I've done a lot of readings with the light sensor and analysed them. If you want to have a look you can go to (URL) . If you look in the appendix of that document you'll find information on the light sensor (and many other things...) Magdalena (21 years ago, 31-Jul-03, to lugnet.robotics.rcx)
|
