 | | Re: SetWatch() is remembered?
|
|
(...) The Watch will reset to 0000 when you turn off device. It gets cleared on power up every time. You can, however, start and stop programs and keep the time. Dean -- -Dean Husby LUGNET Member #320 (23 years ago, 7-Aug-01, to lugnet.robotics.rcx.nqc)
|
| |
| | Re: maximum current of outputs
|
|
(...) 9.3x volts when a Train Power supply is used. Down to as little as 6.5 volts when batteries are getting pretty low. Dean -- -Dean Husby LUGNET Member #320 Co-Founding Member: VLC (23 years ago, 7-Aug-01, to lugnet.robotics.rcx.nqc)
|
| |
| | Re: SetWatch() only accepts constants
|
|
(...) You can use the NQC -watch now command to set the time. Dean (23 years ago, 7-Aug-01, to lugnet.robotics.rcx.nqc)
|
| |
| | Help needed for an NQC newbie
|
|
Hi, Normally you can see me in .space, .loc.ca, or org.ca and the like. But now that I have an RCX I want to program a bit. I have written my first NQC program and compiled it using RCXCC. I then downloaded it to my RCX but when I press run the legs (...) (23 years ago, 7-Aug-01, to lugnet.robotics.rcx.nqc)
|
| |
| | Re: transfer data failed
|
|
(...) I am using 0.2.4 under windoz and have had similar problems. I found that I must use the slow download option (-s) for the firmware to load properly. regards (23 years ago, 7-Aug-01, to lugnet.robotics.rcx.legos)
|
| |
| | RE: SetWatch() is remembered?
|
|
Take the batteries out (and unplug the external power on RIS 1.0) and it forgets everything, Date, Time, Programs/Tasks, even "Firmware"... "ZZZzzzombie" RCX :) mc. (...) (23 years ago, 7-Aug-01, to lugnet.robotics.rcx.nqc)
|
| |
| | SetWatch() is remembered?
|
|
So does this mean that the RCX acts like a PC in that it does not forget the date/time when it is turned off or the batteries changed? Should I just write a one line program to set the time, and remove the time code from my actual NQC program? Thank (...) (23 years ago, 7-Aug-01, to lugnet.robotics.rcx.nqc)
|
| |
| | maximum current of outputs
|
|
Hi hardware-specialists, does anyone know the maximum continuous current that a RCX motor output can drive? (I want to connect a light.) Thanks a lot. Bernd (23 years ago, 7-Aug-01, to lugnet.robotics.rcx.nqc)
|
| |
| | Re: transfer data failed
|
|
(...) Hi, i use 0.2.5 under Cygwin and sometimes i experience the same problem. I dont think its a problem with the legOS 0.2.4 distribution. The problem often occurs if its too dark or too bright in your room. It also happens if sender and receiver (...) (23 years ago, 7-Aug-01, to lugnet.robotics.rcx.legos)
|
| |
| | RCX 2.0 Difference
|
|
I have got both an RCX1.0 and RCX2.0 unit. The RCX2.0 has a much less sensitive IR port. I would use the remote control to send messages and start and stop programs and to trigger motors. With the RCX1.0 the remote could be pointed at the unit and (...) (23 years ago, 7-Aug-01, to lugnet.robotics.rcx)
|
