 | | RCX analog input?
|
|
I haven't been reading any of the LUGNET robotics groups until a month or so ago when I bought my first Mindstorms 1.5 kit and entered into this branch of LEGO. (so sorry if this has been posted before and I haven't seen it in any FAQ's) My question (...) (24 years ago, 27-Jan-01, to lugnet.robotics.rcx)
|
| |
| | Re: thermal sensor
|
|
"Grath" <jgreene750@hotmail.com> wrote in message news:G7s5LD.Bzq@lugnet.com... (...) thermal (...) 12K at room temperature. I've never found one like this, so you use a 10K at room temp thermistor with a 2K in series. There is a lot on this (...) (24 years ago, 26-Jan-01, to lugnet.robotics.rcx)
|
| |
| | Re: Another way to avoid Float
|
|
(...) them. (...) diameter. (...) wheel (...) This is all well and good, but the all consuming problem with location tracking is slippage. What happens if one wheel slips? What about if it hits an obstacle at an angle? If you find some way around (...) (24 years ago, 26-Jan-01, to lugnet.robotics.rcx)
|
| |
| | thermal sensor
|
|
yo whatup, does anybody happen to know what the ohmage on a mindstorms thermal sensor is? im assuming its just a thermal resistor. if any1 can lemme know itll save me the trouble of figuring it out myself with a meter and potentiometer. thanx Grath (24 years ago, 26-Jan-01, to lugnet.robotics.rcx)
|
| |
| | Re: RCX display
|
|
"Andi Scharfstein" <calvin8@t-online.de> wrote in message news:3A7144B8.702040...line.de... (...) The highest level way to get to the display is by using Mindscript. This is a language for the RCX you an get from LEGO. You download it from the main (...) (24 years ago, 26-Jan-01, to lugnet.robotics.rcx)
|
| |
| | RCX display
|
|
Hi, I suppose it must have been done before, because it is so obvious, but I can't seem to be able to find information about it on the web. Can anybody tell me how to access the RCX display directly, that is, for example, display numbers or such? A (...) (24 years ago, 26-Jan-01, to lugnet.robotics.rcx)
|
| |
| | Re: legOS lcd management and thoughts on velocities
|
|
(...) Yes, I have written that support. First you have to enable it, by removing the comments from the line in legOS/boot/config.h. Then recompile the kernel and all apps. After you have programmed the rotation sensor in the usual way you can read (...) (24 years ago, 26-Jan-01, to lugnet.robotics.rcx.legos)
|
| |
| | Visual NQC 2001 Beta 2
|
|
To all testers, Runtime error 380 stands for invalid property. This can happen when you try to compile a program in the editor. I had the error ones during development but it didn't come up anymore. Next week I'm starting bugfixing again and see if (...) (24 years ago, 26-Jan-01, to lugnet.robotics.rcx.nqc)
|
| |
| | How many motors can accept a RCX ?
|
|
Hi, everybody <DISCLAIMER> Excuse me first for my newbieness here on Lugnet. and also for my frenchieness, but it's not my fault ! </DISCLAIMER> I have a question I'd like to submit: Because of extreme needs of power/ acceleration (it was about (...) (24 years ago, 26-Jan-01, to lugnet.robotics.rcx)
|
| |
| | RE: Confusion regarding the POWER_OFF command.
|
|
(...) I was too. It's a bit goofy, so I'll try to explain as I go... (...) That's fine - the only thning you need to do (I think - I'm away from my RCX) is to put POWER_INIT just before POWER_OFF. The POWER_INIT word initializes the interrupt (...) (24 years ago, 25-Jan-01, to lugnet.robotics.rcx.pbforth)
|
