 | | Curious problem with download
|
|
I just got Mindstorm set, and since I do not have a PC, NQC seemed like a great place to start. I tried Mac NQC and did not get very far downloading the RCX firmware. Every attempt resulted in the IR tower not seeing the RCX. I have a G3 blue and (...) (25 years ago, 27-Jan-00, to lugnet.robotics.rcx.nqc)
|
| |
| | Re: LegOS does not work on 1.5 RCX
|
|
Before anyone replies to my previous message, found the problem. I have a light over my desk and this was interfering with the IR transmission. Turned the light off and moved the RCX a little closer to the tower and hey presto, all OK. Does legOS (...) (25 years ago, 27-Jan-00, to lugnet.robotics.rcx.legos)
|
| |
| | LegOS does not work on 1.5 RCX
|
|
Hi I installed the win version of legOS and downloaded the firmware legOS.srec to both my RCX's. The older RCX from a 1.0 set seems to accept .lx files OK the first time after the firmware is downloaded. The new version will not accept any .lx (...) (25 years ago, 27-Jan-00, to lugnet.robotics.rcx.legos)
|
| |
| | more on the rotation sensor
|
|
I did some more experiments last night. My conclusion is that the majority of apparent 2-state transitions never actually occur (that is: the sensor does not actually travel through 2 states between two consecutive sensor readings). The order of the (...) (25 years ago, 27-Jan-00, to lugnet.robotics.rcx.legos)
|
| |
| | legOS timers
|
|
Hi! Did anyone write any 'nicer' wrapper functions for handling the RCX timers? Or am I blind and can't find them? 8^) /Vlad (25 years ago, 27-Jan-00, to lugnet.robotics.rcx.legos)
|
| |
| | FW: installation problem!
|
|
-----Original Message----- From: George Lampke [mailto:glampke@verinet.com] Sent: Thursday, January 27, 2000 12:50 PM To: Ralph Hempel Subject: Re: installation problem! You are right Ralph. Using the command line version of NCQ works to load (...) (25 years ago, 27-Jan-00, to lugnet.robotics.rcx.pbforth)
|
| |
| | RE: installation problem!
|
|
(...) I've only verified pbForth being uploaded using the commandline version of NQC. (...) This is good. Has anyone else out there tried RCXCC to upload the pbForth firmware???? Cheers, Ralph Hempel - P.Eng ---...--- Check out pbFORTH for LEGO (...) (25 years ago, 27-Jan-00, to lugnet.robotics.rcx.pbforth)
|
| |
| | Re: Light sensors
|
|
(...) more light and is working.... Erm... it isn't really working - it exhibits the same 'inverted' behaviour, looking for a white line on a black background... /Vlad (25 years ago, 27-Jan-00, to lugnet.robotics.rcx.legos)
|
| |
| | Light sensors
|
|
Hi! Maybe this is obvious for all experienced legOS users - I am displaying the values read from the light sensor on the LCD, and I get values of ~30 for light and ~520 for darkness... This seems very strange - is it the display wrong, or are these (...) (25 years ago, 27-Jan-00, to lugnet.robotics.rcx.legos)
|
| |
| | Re: Firmware startup bug?
|
|
I have replaced my batteries without erasing the firware several times. The trick is replacing the batteries one at a time with the brick turned off. You have then several (10 or so) seconds between each replace. If you leave the brick switched on (...) (25 years ago, 27-Jan-00, to lugnet.robotics.rcx.legos)
|
