 | | NXC problem
|
|
I've tried to install Bricx and NXC but when I try to compile a simple program I get an error like "Unable to find include file: "NXCDefs.h". I figure I probably just have something configured incorrectly but can't find any guidance as to what I (...) (17 years ago, 28-Dec-07, to lugnet.robotics.nxt)
|
| |
| | Re: recharging NXT battery block with DC adapter?
|
|
(...) The reason asking is that sometimes we send teams of students to a country with different voltage in the outlet, i.e. 110V instead of 220V, and the LEGO adapter accepts 220V, but not 110V. However, we have a DC adapter that accepts both 110V (...) (17 years ago, 20-Dec-07, to lugnet.robotics.nxt)
|
| |
| | NXT, Bluetooth, and Palm
|
|
Ok, so after 7 years of using my faithful Palm Vx, syncing it to my Kubuntu Linux machine at work put something on it to make it fatally crash every time I ran the calendar. Seeing as this was the most important function of the Palm, I decided it (...) (17 years ago, 18-Dec-07, to lugnet.robotics.nxt, lugnet.robotics.palm)
|
| |
| | Colour Sensor
|
|
Which command do I use to initialise my Hitechnic colour sensor under NXC on the NXT? Thanks Steve (17 years ago, 18-Dec-07, to lugnet.robotics.nxt)
|
| |
| | Re: motor command question
|
|
Hi Patty, I can't really answer this question other to say that I had exactly the same problem a while ago. I talked to LEGO tech support to no avail and they actually sent me a replacement block to fix the problem. However when I got it I had (...) (17 years ago, 3-Dec-07, to lugnet.robotics.nxt)
|
| |
| | Re: motor command question
|
|
Because the motors start to turn, then the program reaches the end, and exits. You need to tell the program to "wait for" something after the motors start. Steve (...) (17 years ago, 3-Dec-07, to lugnet.robotics.nxt)
|
| |
| | motor command question
|
|
Why would two motors, set to turn and with unlimited chosen for time out, only turn a couple of times and stop. this motor command is the only command in the program. patty (17 years ago, 3-Dec-07, to lugnet.robotics.nxt)
|
| |
| | Re: Nxc and Mindsensors stuff
|
|
(...) Thank you! But it worked only after firmware upgrade (to version 1.05) and using original NXT flat cables (Mindsensors flat cables are very poor quality). -- alf (17 years ago, 30-Nov-07, to lugnet.robotics.nxt)
|
| |
| | Re: recharging NXT battery block with DC adapter?
|
|
My NXT Charger came with my battery. The output of the charger is 10.8 volts, 700 ma 8W. I would just buy the Lego charger. After reaching a full charge, the charger goes into a trickle charge mode. "Pavel Petrovic" <pavel.petrovic@gmail.com> wrote (...) (17 years ago, 30-Nov-07, to lugnet.robotics.nxt)
|
| |
| | Re: recharging NXT battery block with DC adapter?
|
|
(...) Whew! I was going to put my question in past tense ("Does this mean that I should have or shouldn't have used the train controller plug ...") but it seemed better to be a fool after doing something not dumb than after doing something dumb! (...) (17 years ago, 30-Nov-07, to lugnet.robotics.nxt)
|
