 | | Re: Need help with bumpers connected to the HB
|
|
Hello, Can you describe more about "HB turns itself off ?" Does the HB reset itself? The analog inputs for HB have pull-up resistors. This pull-up resistor may cause the problem. Thanks. Patrick Hui (URL) Original Message ----- From: "Haberlag" (...) (23 years ago, 23-May-01, to lugnet.robotics.handyboard)
|
| |
| | Outputs
|
|
Right now I've got one Sharp GP2D05 IR Ranger rigged to TO3 and another to digital in 9. Those are working fine, but I'd like to add a servo motor, which needs one of those two ports for a signal. The FAQ mentions using the J6 SPI pins, might I be (...) (23 years ago, 23-May-01, to lugnet.robotics.handyboard)
|
| |
| | Need help with bumpers connected to the HB
|
|
Hi, I’ve got a problem in getting started with the Handy Board. I’d like to connect a bumper detection circuit to the analog0 of my HB. But when I connect the bumper circuit to my HB , the HB turns itself off. Can anybody help me? Any help would be (...) (23 years ago, 23-May-01, to lugnet.robotics.handyboard)
|
| |
| | Re: Will not keep P-Code.....
|
|
Rmoving every chips except 62256 RAM and 74HC132, and try it again if it works. Besides the memory chip (62256), please also check the 74HC373 (under-neath the 62256 RAM). Patrick Hui (URL) Original Message ----- From: "Kurt Telep" <kt25@drexel.edu> (...) (23 years ago, 22-May-01, to lugnet.robotics.handyboard)
|
| |
| | Will not keep P-Code.....
|
|
Well, I recently got a hold of a handyboard from a |friend of mine who swore it was "junk and didnt' work" | After cleaning up some ugly looking solder joints on |the board, it powered right up and began to work |great. Well, when I went to screw it (...) (23 years ago, 22-May-01, to lugnet.robotics.handyboard)
|
| |
| | huip@hkstar.com
|
|
Hi, I have two question. 1. I received my IR transmitter from you, but I'm not sure how to attach it (in what direction). 2. I also received the Polaroid sonar system. I wonder if there are any more info available about it beside the datasheet which (...) (23 years ago, 21-May-01, to lugnet.robotics.handyboard)
|
| |
| | Is the Handy Board compatible with Windows ME?
|
|
I have a Gateway Performance (933Mhz) using Windows Millenium Edition. The Handy Board works on other computers (work, school, etc) but not with this one. I follow the HyperTerminal steps & get the message: "Unable to open COM1. Please check your (...) (23 years ago, 19-May-01, to lugnet.robotics.handyboard)
|
| |
| | Re: gcc hb lib
|
|
Kai Schlamp writes: > Can somebody tell me what the assembler directive ".follow" means in the > GCC Handyboard Library written by Curt Mills? I can´t find it in the > documentation of the up to date as6811 version 3.0 and as6811 also > doesn´t (...) (23 years ago, 18-May-01, to lugnet.robotics.handyboard)
|
| |
| | gcc hb lib
|
|
Hy! Can somebody tell me what the assembler directive ".follow" means in the GCC Handyboard Library written by Curt Mills? I can´t find it in the documentation of the up to date as6811 version 3.0 and as6811 also doesn´t assemble the files with this (...) (23 years ago, 17-May-01, to lugnet.robotics.handyboard)
|
| |
| | Re: generating waves
|
|
In lugnet.robotics.handyboard, Matthias Weber writes: I think your best bet would be to create an external oscillator that could be controlled using one of the TOC's. I mention the TOC's in case you need to pulse the oscillation (infrared remote (...) (23 years ago, 17-May-01, to lugnet.robotics.handyboard)
|
