 | | More on Miniboard woes and woohoos.
|
|
Hi again, Thanks to those who sent suggestions. Running in DOS mode, not W95 dlm does work just fine. Ick. Oh well. Anyway, I thought that 2K of EEPROM would be enough to do something with, and it may be, but probably not in ICC - The printf.c (...) (24 years ago, 6-Oct-00, to lugnet.robotics.handyboard)
|
| |
| | Re: Miniboard download random failures
|
|
(...) "expected (...) James, Yes, I am running from a DOS window in W9X. Do I have to boot to DOS mode to correct for this? Uhm, I'm a Mac person, so, have patience, how does one boot to DOS instead of Win95? thanks, DLC (24 years ago, 5-Oct-00, to lugnet.robotics.handyboard)
|
| |
| | Re: Miniboard download random failures
|
|
(...) Are you running DLM from a dos window in Win9x? I've had this problem but it usually stops when I run it in DOS. Just a thought. -Jim Munro <jimmn@xnet.com> (24 years ago, 5-Oct-00, to lugnet.robotics.handyboard)
|
| |
| | Freeware ICC11 and bad iasm11.exe?
|
|
Me again, I just got the ICC11 freeware from the Miniboard site and installed it, moving the crt.s over as it says to do in the docs, etc. I tried to compile the test compile of icc11 dhry.c printf.c and got a LOT of "phasing" errors, whatever that (...) (24 years ago, 5-Oct-00, to lugnet.robotics.handyboard)
|
| |
| | Miniboard download random failures
|
|
Hello, I just finished building a Miniboard using the HC811E2 processor. After swapping the Rx and Tx lines on my serial cable the download and reset switch do as the manual says. However, when I use dlm to download a program the bootstrap section (...) (24 years ago, 5-Oct-00, to lugnet.robotics.handyboard)
|
| |
| | serial communication
|
|
Hi.. I am also facing problem in serial communications. My problem is that I am trying to use the handyboard to drive a modem. I have used a cross-serial cable to connect my handyboard's external serial board to a modem. But whenever I run my app, (...) (24 years ago, 5-Oct-00, to lugnet.robotics.handyboard)
|
| |
| | R: communication via serial port
|
|
Using java and comm API ? ----- Original Message ----- From: Ray Tang <raytang_1@hotmail.com> To: <handyboard@media.mit.edu> Sent: Thursday, October 05, 2000 4:49 AM Subject: communication via serial port (...) and (...) the (...) a (...) (24 years ago, 5-Oct-00, to lugnet.robotics.handyboard)
|
| |
| | Linux and v1.21 handyboard (fwd)
|
|
Hi, I've successfully located and compiled the IC files for the Handy Board. I can load and run programs on the board, BUT the digital input(s) are not being "seen". E.g. a simple program like: void test3(){ while (1){ if (digital(10)) printf("10 is (...) (24 years ago, 5-Oct-00, to lugnet.robotics.handyboard)
|
| |
| | communication via serial port
|
|
Hi, This isn't an off topic question... Has anyone tried programming the serial port (on Linux) to communicate with the Handyboard? I am working on an RF link between the Handyboard and a PC via serial communication, but I don't know much about (...) (24 years ago, 5-Oct-00, to lugnet.robotics.handyboard)
|
| |
| | Re: external power
|
|
I am by no means an expert on the subject but this is how I did it. First I cut the heavy motor power trace as shown in the FAQ. Next I soldered a four pin female header on top of the expansion board where the expansion board picks up power for the (...) (24 years ago, 4-Oct-00, to lugnet.robotics.handyboard)
|
