| | Re: HB Memory map
|
|
Device Location Notes ===...=== 6811 internal $0000-$00ff Built-in RAM (A1 chip) $0000-$01ff (E1 chip) ---...--- 6811 control $1000-$103f Built-in registers ---...--- Expansion I/O $4000-$4fff Memory reads in this range enable the Y1 latch selector, (...) (24 years ago, 14-Jun-00, to lugnet.robotics.handyboard)
|
|
| | Re: Motors spinning at startup
|
|
The problem is the same with LEGO-gear-motors. Even worse, the post says "... put a wire to the can ..." but how can you do this with a plastic device? Any help appreciated. Dirk (24 years ago, 14-Jun-00, to lugnet.robotics.handyboard)
|
|
| | Motors spinning at startup
|
|
Hi all, I have a problem with the motors connected to my handyboard. When I first turn on the HB, the motors will spin randomly. This happens about every 2-3 times I switch on. I know this problem has come up before on the list, but the post I found (...) (24 years ago, 13-Jun-00, to lugnet.robotics.handyboard)
|
|
| | Proposition
|
|
HEALTH: A NEW NATURAL HELP To the product Manager The customers demand for natural products is increasing steadily, and Aromatherapy is becoming an important part of the pharmacopoeia. The Aromagica line of products is the outstanding result of (...) (24 years ago, 13-Jun-00, to lugnet.robotics.handyboard)
|
|
| | HB Memory map
|
|
This probably sounds like a pretty lame question but I am trying to make use of the unused areas in the lower 32K of the memory map of the HB but I can't seem to find the memory map in the documentation that I have available (the HB pdf manual, IC (...) (24 years ago, 12-Jun-00, to lugnet.robotics.handyboard)
|
|
| | circuitboards for Handyboard
|
|
Hi. Are the circuitboards for the Handyboard available somewhere in Europe? Regards/Mvh. John Jensen (24 years ago, 12-Jun-00, to lugnet.robotics.handyboard)
|
|
| | Motor Masks***
|
|
Hi , does anyone know if there are specific moter masks already defined for the HB? Or can I just initialize them anywhere there is free memory? Thanks -Mike (24 years ago, 9-Jun-00, to lugnet.robotics.handyboard)
|
|
| | RE: fast computer problems
|
|
Still no luck! any other ideas ??? - what baud rate is the port meant to be set at? 9600? Thanks again Ross -----Original Message----- From: Gary Livick [mailto:glivick@pacbell.net] Sent: 05 June 2000 08:25 To: The Glashans Cc: (...) (24 years ago, 6-Jun-00, to lugnet.robotics.handyboard)
|
|
| | SCI, IC and interrupts
|
|
Hi I need to communicate with my handy board using the serial port using the Interrupt for SCI. I tried to test several programs that I found, without success. My basic test is the following. 1.- I created and .asm file which is a copy of the (...) (24 years ago, 5-Jun-00, to lugnet.robotics.handyboard)
|
|
| | Re: fast computer problems
|
|
What works on my computer is to go into the port settings, set XON-XOFF, and then enable the FIFO buffer and turn the speeds all the way up. I have a Toshiba laptop, so hopefully your settings will be the same. If I do it any other way under WIN98, (...) (24 years ago, 5-Jun-00, to lugnet.robotics.handyboard)
|