 | | Did I fry my Polaroid unit?
|
|
Today, I started trying to use my Polariod Sonar unit pulled from a Polaroid OneStep Sun 660 Camera. I didn't get the hang of it the first time. I desoldered the connector and put on wires. Then I plugged it in backwards. Oops. The chips started (...) (24 years ago, 3-Jun-00, to lugnet.robotics.handyboard)
|
| |
| | Where to find program examples?
|
|
Hi I recently purchased a Hb, does anyone know where I can find examples for programming it? Also is the IC code for the rug Warrior the same as the IC for the HB? Thanks -Mike (24 years ago, 2-Jun-00, to lugnet.robotics.handyboard)
|
| |
| | Re: Ic question
|
|
As far as I know, the infinite loop construct is the way to do it. However, you can have multiple processes, each waiting on a sensor, each running in an infinite loop, each using the defer() function to allow switching between processes when (...) (24 years ago, 2-Jun-00, to lugnet.robotics.handyboard)
|
| |
| | Sharp GP2D12 & Sony IR Receiver
|
|
Is there SOMEONE that can run SHARP GP2D12 analog sensor when using IR RECEIVER? I couldn't achieve that. The sensor can give satisfactory results it is used without alone. I can also get data of a sony remote controller from the ir receiver when (...) (24 years ago, 2-Jun-00, to lugnet.robotics.handyboard)
|
| |
| | Ic question
|
|
I have been playing around with my handy in command line for a little while now. It seems like the only way I can get it to start doing something when a sensor is activated is to have it in an infinite loop waiting for that sensor to be pressed. For (...) (24 years ago, 2-Jun-00, to lugnet.robotics.handyboard)
|
| |
| | Re: Got my Handy, now what?
|
|
(...) The The Handy Board Technical Reference has encoder information for you. The ones I use are the QRB1114, and they are just two or three dollars each. The Reference shows you how to wire them. See (URL) encoders mentioned provide an analog (...) (24 years ago, 2-Jun-00, to lugnet.robotics.handyboard)
|
| |
| | Got my Handy, now what?
|
|
I ordered my Handy Board today, and am going to install it in an ice cream bucket named "BucketBot." (Better name? Please?) Well I know that I'll be hooking up my GP2D12 to it, and a sonar module (Polaroid 6500 hacked out of a Polaroid Sun 660 One (...) (24 years ago, 2-Jun-00, to lugnet.robotics.handyboard)
|
| |
| | Re: XC68HC11F1B4 Pin assignments
|
|
in article 393601FD.1DF@hemo.net, Zele at 4n7ax@hemo.net wrote on 5/31/00 11:26 PM: (...) I found the documentation for the MC68HC11F1 series on the Motorola web site at this URL: (URL) documentation is in an 848k PDF file: (URL) picture you're (...) (24 years ago, 31-May-00, to lugnet.robotics, lugnet.robotics.handyboard)
|
| |
| | XC68HC11F1B4 Pin assignments
|
|
Hello, I have few XC68HC11F1B4 in 64-pins plastic SDIP, but can not find any data about pin assignments for this chip. Can somebody to help me with it ? Please e-mail to: 4n7ax@hemo.net Z. Ristic (24 years ago, 31-May-00, to lugnet.robotics.handyboard)
|
| |
| | XC68HC11F1B4 Pin assignments
|
|
Hello, I have few XC68HC11F1B4 in 64-pins plastic SDIP, but can not find any data about pin assignments for this chip. Can somebody to help me with it ? Please e-mail to: 4n7ax@hemo.net Z. Ristic (24 years ago, 1-Jun-00, to lugnet.robotics, lugnet.robotics.handyboard)
|
