 | | RE: hellofriend
|
|
Yes, definitely spam! | -----Original Message----- | From: Meabadboy@aol.com [mailto:Meabadboy@aol.com] | Sent: Sunday, May 14, 2000 3:48 AM | To: handyboard@media.mit.edu | Subject: Fwd: hellofriend | | | SPAM??? | | (24 years ago, 14-May-00, to lugnet.robotics.handyboard)
|
| |
| | using 3v motors?
|
|
Is there any way to use 3 volt motors on the Handyboard? They draw about 400 ma. Using a series resistor of about 10 ohms works, but it will have to be about 5 watts, consuming a lot of power needlessly. The FAQ shows how to run 6-36v motors through (...) (24 years ago, 14-May-00, to lugnet.robotics.handyboard)
|
| |
| | Fwd: hellofriend
|
|
SPAM??? (24 years ago, 14-May-00, to lugnet.robotics.handyboard)
|
| |
| | hellofriend
|
|
Date:14th.may,2000 Dear sir, it give us pleasure to request your indulgence in this extremely CONFIDENTIAl business proposition which we want you to handle for us IN YOUR PRIVETE CAPACITY. This total believe and reponse of trust in you, is in (...) (24 years ago, 13-May-00, to lugnet.robotics.handyboard)
|
| |
| | Running as11
|
|
Hi, Has anyone been able to run as11 on a Mac? As a first test of the assembler, I've been trying to re-assemble pcode.asm, without success. Specifically, as11 balks at the preprocessor directives. I tried running pcode.asm through the CodeWarrior (...) (24 years ago, 13-May-00, to lugnet.robotics.handyboard)
|
| |
| | Re: Household Positioning System Re: DGPS
|
|
I see. Humm. May be I can really use this. OK, if I put a few IR LED with ID at different locations in the room, and put them at the same height as the robot sensor so I don't need to worry about tilt angle. If I put the sensor fixed on the robot, (...) (24 years ago, 12-May-00, to lugnet.robotics.handyboard)
|
| |
| | Re: Household Positioning System Re: DGPS
|
|
Actually, I am going in that direction. I was trying to use the ultrasonic transducer to produce a signal and then use two detector to triangulate the location. That wasn't much of a success. I will need to redo the parts. I want to try using more (...) (24 years ago, 12-May-00, to lugnet.robotics.handyboard)
|
| |
| | Re: Household Positioning System Re: DGPS
|
|
(...) Some years ago i wrote the presentation part of a prototype system based on ultrasonic beacons. the beacons were plugged into wall outlets and transmitted their ID:s, i can't remember the details but the beacons were syncronized by (...) (24 years ago, 11-May-00, to lugnet.robotics.handyboard)
|
| |
| | Re: Household Positioning System Re: DGPS
|
|
(...) No design, just an idea. The way I see it, you put a "Head" on the top of your robot. It has three sensors mounted for tilt and pan. The easiest way I can see it is to use gear head stepper motors with a "Home" switch to point the thing. The (...) (24 years ago, 11-May-00, to lugnet.robotics.handyboard)
|
| |
| | (no subject)
|
|
unsubscribe (24 years ago, 11-May-00, to lugnet.robotics.handyboard)
|
