To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.robotics.handyboardOpen lugnet.robotics.handyboard in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / Handy Board / *7529 (-10)
  dead hb - alive again
 
hello. seems my dead handyboard problem of yesterday was a result of a bad adapter, not the board itself. a relief. thanks, claudia (24 years ago, 23-Mar-00, to lugnet.robotics.handyboard)
 
  Re: Handyboard in mix with SSC II Servo Controller
 
Hi, There are several steps you should follow. 1..Download the 9600 serial driver form (URL) you that if you use SSC controllers, download the inverted version. 2...Refer to you SSC manual, connect the serial in pin to PA7 of handyboard, PA7 is the (...) (24 years ago, 23-Mar-00, to lugnet.robotics.handyboard)
 
  dead hb - overpowered?
 
hello. i used the wrong dc adapter (15v) to power my hb today. i made the switch to the proper adapter (12v) fairly quickly, and things seemed fine - i was able to download the pcode. but when i rebooted the board, the power died and i've not been (...) (24 years ago, 23-Mar-00, to lugnet.robotics.handyboard)
 
  Re: resistor pull-up help!
 
basically, yes. the inputs from the expansion board feed into the inputs on the main board. if you need a high impedance input, your best bet is to cut a trace on the main board and use one of those inputs. the exp bd takes over main board inputs 0 (...) (24 years ago, 23-Mar-00, to lugnet.robotics.handyboard)
 
  RE: resistor pull-up help!
 
Hi, Are the general-purpose analog inputs in the exp board also connected to the pull-up in the HB main? To use that kind of sensors the only way is to cut the trace in the HB, no matter I have or no the ExpBoard? Thanks Jose Luis --- Original (...) (24 years ago, 23-Mar-00, to lugnet.robotics.handyboard)
 
  Re: Required tools for assembly
 
I have a really nice, and very expensive (somebody gave it to me), Tech 2432A dual trace scope with storage. I have also built about 20 boards of various kinds, some of my own design. The scope has lots of dust on it, although it looks great on the (...) (24 years ago, 22-Mar-00, to lugnet.robotics.handyboard)
 
  Handyboard in mix with SSC II Servo Controller
 
Hi, We are trying to conntect Handyboard to SSC II Mini Servo Controller so we can control more servo motors. Can anyone tell us how to connect these two pieces and work them together? Also, where is the serial output of the Handyboard, and ground? (...) (24 years ago, 22-Mar-00, to lugnet.robotics.handyboard)
 
  Re: recharging battery
 
(...) You will need some good equipment, or you will need lots of patience and a good DVM. Here are the steps to rejuvinating old NiCds IF they can be recovered. If they have suffered the effects of overcharging (common) then they may not be (...) (24 years ago, 22-Mar-00, to lugnet.robotics.handyboard)
 
  Re: Interfaced your Sonar with HB
 
Hi Everyone! It looks like Frankie Lai has found a way to interface the sonar I have on my site to the HB. Here are his comments: (...) hihi, me again......I think you know already, but I would like to precise it. The echo line through NOT gate is (...) (24 years ago, 22-Mar-00, to lugnet.robotics.handyboard)
 
  Pull-up resistors
 
I would like to attach a LM34 to my miniboard. In testing the LM34 at a room temperature of 60F, the device gives me a reading of .6V. The docs say that every 10mv=1F, so it seems to be working correctly. When I attach it to one of the analog ports (...) (25 years ago, 22-Mar-00, to lugnet.robotics.handyboard)


Next Page:  5 more | 10 more | 20 more

Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR