 | | Hitachi LM052-L
|
|
Hello, my Hitachi LM052-L display is damaged. Does anybody know where to buy a new one or equivalent in Europe ? Or how to test which part is damaged of the handyboard display system or the display itself ? Thank You ! Jan Luijk Netherlands (27 years ago, 15-Mar-00, to lugnet.robotics.handyboard)
|
| |
| | Q: 10 dc motors on handyboard?
|
|
Does anyone know if handyboard can run more than four dc-motors? I want to be able to control a complex lego construction, with full control of all motors at once. The current flow shouldn't be to dramatic, I hope. I would also like to ask how it is (...) (27 years ago, 15-Mar-00, to lugnet.robotics.handyboard)
|
| |
| | Re: Overcharged battery?
|
|
hi dennis, well, it's just a plain C/10 charge circuit. but i was under the impression that nicad's aren't damaged by that. it's possible i'm wrong :-). any other battery experts out there? fred In your message you said: (...) ly (...) ut (...) (27 years ago, 15-Mar-00, to lugnet.robotics.handyboard)
|
| |
| | Re: Overcharged battery?
|
|
(...) I was guessing here - most chargers don't check for peak charge, since I didn't know if the Handiboard charger did or didn't... If the charger has a trickle charge of more than C/50 or C/100 then NiCds will be damaged eventually on a long-term (...) (27 years ago, 15-Mar-00, to lugnet.robotics.handyboard)
|
| |
| | Re: Vector 2X driver
|
|
I just bought a Vector 2X electronic compass for a project. In looking at it the manual, I see that if the 2X is run in slave mode I can clock out data from it at my leisure using any digital pins available on the Handy Board. This could almost be (...) (27 years ago, 15-Mar-00, to lugnet.robotics.handyboard)
|
| |
| | Re: Overcharged battery?
|
|
no i disagree with this answer. the HB is designed to be left on normal charge indefinitely. the batts can get a little warm. if they are hot then something is wrong, but a little warm is nothing to worry about. when fully charged and with no load (...) (27 years ago, 15-Mar-00, to lugnet.robotics.handyboard)
|
| |
| | Re: Non-polaroid Sonar
|
|
In the sonar code from the web site, the rising edge detection on timer input channel 3 (TIC3) is set like this: bit_clear( 0x1021, 2 ); bit_set( 0x1021, 1 ); According to the little pink book, address 0x1021 is the Timer Control Register 2 (TCTL2) (...) (27 years ago, 15-Mar-00, to lugnet.robotics.handyboard)
|
| |
| | Re: Overcharged battery?
|
|
(...) Ouch. You don't want to do that too much or you will torch (may have torched) your NiCds. NiCds do NOT like to be overcharged, it causes a problem called Voltage depression that many mistakenly call "memory effect". [snip] (...) Servos will (...) (27 years ago, 15-Mar-00, to lugnet.robotics.handyboard)
|
| |
| | Re: Overcharged battery?
|
|
actually this is to be expected. with no load, the diodes produce no drop. if you're worried, try hooking a DC motor (or other real load -- light bulb, 10 ohm resistor, etc). across the servo motor supply and then measure the voltage. you should see (...) (27 years ago, 15-Mar-00, to lugnet.robotics.handyboard)
|
| |
| | Overcharged battery?
|
|
I've got a pre-assembled Gleason Research HB with expansion board, and have a couple questions. We've left it plugged in (on normal charge mode) for a week or so. I started to look at the specs to hook up a Futaba servo (6V), and found that with no (...) (27 years ago, 15-Mar-00, to lugnet.robotics.handyboard)
|
