 | | Analog/Digital IO
|
|
I know this question does not really relate to the handyboard, but does anyone know of a cheap PCI or ISA card for a PC to read analog or digital values? Thanks, Mike Reiling (25 years ago, 3-Feb-00, to lugnet.robotics.handyboard)
|
| |
| | stepper motor sequence [DAT]
|
|
hi all i was trying to connect a uni polar stepper motor with the hb. i was using the stepping sequence given in peter harrison page. A B C D 1 0 0 0 0 0 1 0 0 1 0 0 0 0 0 1 This sequence means that each coil will be energised one by one. and at no (...) (25 years ago, 3-Feb-00, to lugnet.robotics.handyboard)
|
| |
| | Re: 12V servo motors
|
|
Since the HB battery is only 9.6 V, a 12 V motor would most likely draw too much current and pop the circuit breaker (or worse). I don't see why you couldn't power the servos with a separate 12 V battery, though. The HB expansion board is all set up (...) (25 years ago, 2-Feb-00, to lugnet.robotics.handyboard)
|
| |
| | 12V servo motors
|
|
hi, The HB FAQ says to use 6V servo motors connected to the batt supply with a couple of series diodes to reduce the voltage. can i use 12V servos instead? cheers fazal (25 years ago, 2-Feb-00, to lugnet.robotics.handyboard)
|
| |
| | RE: More servo stuff
|
|
Hi. We have a problem with servo as well. When we test one servo motor, it works just fine. But when we test more than one, the speed of each servo decreases. Does anyone have similar problem? Thanks for your help. Damee Choi (25 years ago, 1-Feb-00, to lugnet.robotics.handyboard)
|
| |
| | Radio Communication and the Handy Board
|
|
In 1998 I made a mobile robot that communicates with a desktop computer using a radio module. Shortly after I accomplished this I made a webpage showing the results. Recently I moved to this page to another location. I invite you all to take a look (...) (25 years ago, 29-Jan-00, to lugnet.robotics.handyboard)
|
| |
| | Re: Video Transmitters
|
|
Yeah, I think it was free for a first time customer! -- Ray Gary Livick <handyboard@media.mit.edu> wrote in message news:383C71AB.C0C8B2...ell.net... I received the X-10 cam I ordered two days ago. It arrived right on time, and is pretty impressive (...) (25 years ago, 29-Jan-00, to lugnet.robotics.handyboard)
|
| |
| | Re: IR detection
|
|
Yeah. It is a material that will illuminate when a IR source shines a beam on it. -- Ray Dovi Poznanski <handyboard@media.mit.edu> wrote in message news:3837E5F9.517BC7...u.ac.il... hey does anybody know how an IR sensor card works? -- Dovi (...) (25 years ago, 29-Jan-00, to lugnet.robotics.handyboard)
|
| |
| | ratings of stepper and servo motors
|
|
hi all what are the ratings (voltages and currents loads) of stepper and servo motors compatible with the handy board. cheers fazal (25 years ago, 28-Jan-00, to lugnet.robotics.handyboard)
|
| |
| | Re: HandyBoard died
|
|
I am sorry to hear about your situation, but I would like to point out that this sort of thing is exactly why the handyboard could, I believe, benefit from having a durable case made for it, which provides all access to the handyboard's (and (...) (25 years ago, 28-Jan-00, to lugnet.robotics.handyboard)
|
| |
| | test
|
|
Testing (25 years ago, 27-Jan-00, to lugnet.robotics.handyboard)
|
| |
| | Re: PID Control
|
|
(...) Yep ... and no. The following was applied to a pneumatic cylinder controlled via an Amplicon Liveline I/O card and an SMC proportional valve (ie not Lego). code ***...*** pidloop: 'e = error, sp = set point (desired value), pv = process value (...) (25 years ago, 27-Jan-00, to lugnet.robotics.handyboard)
|
| |
| | RE: PID Control
|
|
This sounds like the sort of software that would be benifitial to everyone working with the Handyboard, perhaps it could be posted on the HB site? Fred? Reagrds, Matt (...) (25 years ago, 27-Jan-00, to lugnet.robotics.handyboard)
|
| |
| | Re: PID Control
|
|
Hi Mike: May I obtain also the code that you mentioned? I'm supposing the code was used at the HandyBoard? Thanks in advance for your help... Victor G. Ruiz Aranda ruizvic@mx1.ibm.com IBM de Mexico S.A. Coordinador IAS Planta de Manufactura T/L (...) (25 years ago, 27-Jan-00, to lugnet.robotics.handyboard)
|
| |
| | Re: colour sensor
|
|
I would suggest that the sensors are picking up IR. I would wager that your color filters are passing the IR with little attenuation and that your sensors are peaked in the IR region and little affected by the visible color information. If you have (...) (25 years ago, 27-Jan-00, to lugnet.robotics.handyboard)
|
| |
| | Re: colour sensor
|
|
(...) I posted to this yesterday, but my reply seems to have not appeared. What you need to have, is four sensors, not three. The fourth has no filter, and measures 'ambient' light. You then need to compare the return from this, to the other three (...) (25 years ago, 27-Jan-00, to lugnet.robotics.handyboard)
|
| |
| | HandyBoard died
|
|
Hi all! I have some troubles with my HB. I have set it up together with the expansion board, and it worked properly and very fine. Then once, unfortunately, the LCD, connected to the expansion board, touched one of the five motor-power diodes, and (...) (25 years ago, 27-Jan-00, to lugnet.robotics.handyboard)
|
| |
| | Re: PID Control
|
|
Bill I have code in QuickBasic and C, would this be any good to you?? It was code that I used at Uni and both versions have been tested on real apps so I know they work. For example, I developed a pneumatic cyclinder controller based on the QB (...) (25 years ago, 27-Jan-00, to lugnet.robotics.handyboard)
|
| |
| | PID Control
|
|
Has anyone out there developed a good PID control program in IC. I didn't want to reinvent the wheel if it was already available. Thanks Bill Denzel (25 years ago, 27-Jan-00, to lugnet.robotics.handyboard)
|
| |
| | Re: colour sensor
|
|
(...) I have typically used phototransistors rather than CDS photocells but both will work depending on the application. Sensors are like computer programs, when they do one thing they are fairly easy, if they do multiple things they are more (...) (25 years ago, 26-Jan-00, to lugnet.robotics.handyboard)
|
