 | | 9.6V POWER AND 9V MOTORS
|
|
Question? The 9.6v battery in the HB is ideal for running 9v motors, correct? So wouldn't it be true that the motors of an R/C car which also has a 9.6v battery be 9v??? How do you go about finding the voltage and current drawn in a DC motor??? (...) (27 years ago, 29-Sep-99, to lugnet.robotics.handyboard)
|
| |
| | Re: PCODER22.S19
|
|
Your loading the wrong pcode file, you need to load pcode_hb.s19, not pcoder22.s19 Matt -----Original Message----- From: Paul DaCosta <germano@voicenet.com> To: Handyboard <handyboard@media.mit.edu> Date: 28 September 1999 16:57 Subject: (...) (27 years ago, 28-Sep-99, to lugnet.robotics.handyboard)
|
| |
| | PCODER22.S19
|
|
hey everyone, i need help i cannot download ic to my hb, i followed the instructions, but it doesn't work. I keep getting a message like this" cannot find file pcoder22.s19" what's up with this, can someone tell me the right way of downloading ic to (...) (27 years ago, 28-Sep-99, to lugnet.robotics.handyboard)
|
| |
| | Lo-Tech for Hi-Tech swaps, anyone?
|
|
I plan to use the Handyboard within a Course on Interfacing, Microcontroller and Assembly Language Programming at undergraduate level here, starting next month. It turns out that there is a PCB production facility here in Zimbabwe which is now (...) (27 years ago, 28-Sep-99, to lugnet.robotics.handyboard)
|
| |
| | (canceled)
|
|
|
| |
| | hbtest.c
|
|
Hi, I'm assembling a handyboard and am at the stage where the digital inputs are tested using the testdigitals() function of hbtest.c. The test partially works, and I get the beeps after pressing the start and stop buttons, but when I jumper the (...) (27 years ago, 28-Sep-99, to lugnet.robotics.handyboard)
|
| |
| | Re: Problem with bootstrap mode
|
|
Hi Raj - - Trickle charge the battery for awhile (with the HB turned off), then try it again. Good luck, - Nick - (...) (27 years ago, 27-Sep-99, to lugnet.robotics.handyboard)
|
| |
| | Problem with bootstrap mode
|
|
Hi I am having hard time in putting my handyboard in bootstrap mode. I didn't used my board in months , so it run out off power. when i tried to use it display is not working properly. The first line of the display is not working. when i swithed on (...) (27 years ago, 27-Sep-99, to lugnet.robotics.handyboard)
|
| |
| | Re: Analog I/O as Digital I/O
|
|
Also, the "digital(int p)" extends to the analog ports too. When used with a port that is analog in hardware, it just uses 127 as a threshold value to return 1 or 0 (note below 127 returns true). See page 22 in the HB manual. However, with this (...) (27 years ago, 27-Sep-99, to lugnet.robotics.handyboard)
|
| |
| | Re: Analog I/O as Digital I/O
|
|
(...) Since the analog inputs read voltage levels, you should be able to just plug in any switch or 5-0volt input directly. To read the values, use the analog command, and in theory you should only get two possible values, 255 for +5volts, and 0 for (...) (27 years ago, 27-Sep-99, to lugnet.robotics.handyboard)
|
