| | Re: Analog I/O as Digital I/O
|
|
Also, the "digital(int p)" extends to the analog ports too. When used with a port that is analog in hardware, it just uses 127 as a threshold value to return 1 or 0 (note below 127 returns true). See page 22 in the HB manual. However, with this (...) (25 years ago, 27-Sep-99, to lugnet.robotics.handyboard)
|
|
| | Re: Analog I/O as Digital I/O
|
|
(...) Since the analog inputs read voltage levels, you should be able to just plug in any switch or 5-0volt input directly. To read the values, use the analog command, and in theory you should only get two possible values, 255 for +5volts, and 0 for (...) (25 years ago, 27-Sep-99, to lugnet.robotics.handyboard)
|
|
| | Analog I/O as Digital I/O
|
|
Can the analog input lines be used as a digital input lines (if there is no requirement of analog input)? Because, these lines are connected to the port E of 68hc11, then what are modifications required in the code? Asim Kar. City University of Hong (...) (25 years ago, 27-Sep-99, to lugnet.robotics.handyboard)
|
|
| | Serial transmiter
|
|
Does anyone know of a 9600(8,N,1) serial port transmitter? Or have plans for one? I need one for a telepresence robot that I am designing, Also it needs to be as high of power as it can be I am a HAM novice if it makes a difference Andrew Holland (...) (25 years ago, 25-Sep-99, to lugnet.robotics.handyboard)
|
|
| | Re: Using 12V supply with Expansion Board?
|
|
Duhhhh....don't forget to put heat sink on the 293 motor drivers or else you will fry it! Thank You Bart Chrijver for the reminding. Rob (25 years ago, 25-Sep-99, to lugnet.robotics.handyboard)
|
|
| | Re: Using 12V supply with Expansion Board?
|
|
At 12:13 AM 9/25/99 -0700, you wrote: I've look at the electrical schematic for both the Handy Board and Expansion and this is what I got. Because the expansion board only share the handy board's motor output for its Servo outputs, I don't think you (...) (25 years ago, 25-Sep-99, to lugnet.robotics.handyboard)
|
|
| | [OT] HandyBoard batteries
|
|
Hi All: Found: An excellent source for inexpensive HB batteries. They are new 2 AA (800mAh) cells in series for US$0.99 each. I bought 12 of them for $7.14 ... connected four of them in series and added a female connector ... added a male connector (...) (25 years ago, 25-Sep-99, to lugnet.robotics.handyboard)
|
|
| | Re: error when loading *.icb file
|
|
this is a known problem. see the FAQ: (URL) your message you said: (...) (25 years ago, 24-Sep-99, to lugnet.robotics.handyboard)
|
|
| | Re: error when loading *.icb file
|
|
I had the same problem. When I run as11-ic on my MAC, I have no problem. When I do it on an IBM clone, I cannot load it into the Handy Board. I fixed it by hand-editing out the comment line (its in human language) in the generated .s19 file and it (...) (25 years ago, 24-Sep-99, to lugnet.robotics.handyboard)
|
|
| | EXTENSION BOARD
|
|
I every one, I have a problem, is it possible to have an extension board connected to the HB, and at the same time have a seperate motor power source? The reason I'm asking this is because that the "seperate motor power source" and "extension board" (...) (25 years ago, 24-Sep-99, to lugnet.robotics.handyboard)
|