 | | [OT] HandyBoard batteries
|
|
Hi All: Found: An excellent source for inexpensive HB batteries. They are new 2 AA (800mAh) cells in series for US$0.99 each. I bought 12 of them for $7.14 ... connected four of them in series and added a female connector ... added a male connector (...) (25 years ago, 25-Sep-99, to lugnet.robotics.handyboard)
|
| |
| | Re: error when loading *.icb file
|
|
this is a known problem. see the FAQ: (URL) your message you said: (...) (25 years ago, 24-Sep-99, to lugnet.robotics.handyboard)
|
| |
| | Re: error when loading *.icb file
|
|
I had the same problem. When I run as11-ic on my MAC, I have no problem. When I do it on an IBM clone, I cannot load it into the Handy Board. I fixed it by hand-editing out the comment line (its in human language) in the generated .s19 file and it (...) (25 years ago, 24-Sep-99, to lugnet.robotics.handyboard)
|
| |
| | EXTENSION BOARD
|
|
I every one, I have a problem, is it possible to have an extension board connected to the HB, and at the same time have a seperate motor power source? The reason I'm asking this is because that the "seperate motor power source" and "extension board" (...) (25 years ago, 24-Sep-99, to lugnet.robotics.handyboard)
|
| |
| | error when loading *.icb file
|
|
Hi, I have downloaded the as11 assembler. When I assemble a *.asm file, a *.icb file was created. Then I whated to load the file in the HB but the message "Fatal internal error: Illegal line in .s19 file" was dispayed on the monitor. What's the (...) (25 years ago, 24-Sep-99, to lugnet.robotics.handyboard)
|
| |
| | No objection
|
|
Gary Livick wrote: <snip> (...) I don't mind that sort of solicitation. I think it's great that you're helping the Handy Board community by developing HB robotics accessories. I might end up being a customer when you get it up & running. Good luck (...) (25 years ago, 24-Sep-99, to lugnet.robotics.handyboard)
|
| |
| | OptoIsolators
|
|
Regarding the serial port isolator (opto-isolators are good for this) you might see if www.blackbox.com has something along those lines. You could also look up parts similar to the 4N33 to see if you could use something like that in a design. Not (...) (25 years ago, 23-Sep-99, to lugnet.robotics.handyboard)
|
| |
| | Using 12V supply with Exp Board (2nd posting)
|
|
Hi all, This is a second posting of the question I posted up several days ago. So I apologize in advance for any inconvenience if you've already got my first posting. Anyways, I am currently using the 9.6V supply voltage on the HB and hoping to step (...) (25 years ago, 23-Sep-99, to lugnet.robotics.handyboard)
|
| |
| | Computer Serial Port Optoisolator
|
|
This is somewhat off subject, but I am looking for a circuit schematic that will show how to build a serial port optoisolator for my computer. The problem I am having is that once in a while I wire a circuit wrong and end up putting 115V onto the (...) (25 years ago, 23-Sep-99, to lugnet.robotics.handyboard)
|
| |
| | Re: OVER 1 AMP
|
|
Dear Paul, I have an H-bridge that I designed to run big motors. It runs at two amps continuous, and three amps intermittantly. It uses 5 volts for logic from your Handyboard, and 12 volts from a gel cell to run the motors. It also has an analog (...) (25 years ago, 23-Sep-99, to lugnet.robotics.handyboard)
|
