 | | Re: Interfacing handyboard with Basic Stamp2
|
|
Hi, You can use the SPI interface and have the BS2 as a master. The BS2 then defines the clockspeed, because the slowest speed you can select on the 6811 is probably to high for the BS2. It is very simple to use this interface. See the "pink book" (...) (25 years ago, 27-Jul-99, to lugnet.robotics.handyboard)
|
| |
| | Re: Voice Recognition Hardware
|
|
I actually bought one of these units (used) but have been unable to find out anything at all about them beyond the canned software. Any hints as to any sources? Ken McKinnon klmckin@magmacom.com (...) (25 years ago, 27-Jul-99, to lugnet.robotics.handyboard)
|
| |
| | Re: HB Serial line speed change
|
|
(...) I haven't looked at the schematics for the handyboard for a while, but if you use an E-series processor, then I think you can go up to 12MHz (3 MHz E-Clock). I'm not sure whether the rest of the Handyboard could take the increased speed, and (...) (25 years ago, 26-Jul-99, to lugnet.robotics.handyboard)
|
| |
| | Interfacing handyboard with Basic Stamp2
|
|
Hello to everybody. I would like to ask if is possible to interface the handyboard with the basic stamp2 using not the RS232. Thanks beforehand. (25 years ago, 26-Jul-99, to lugnet.robotics.handyboard)
|
| |
| | Re: Weak Motor
|
|
(...) It wouldnt be wise to directly connect your 12V supply to the Handy Board... even if it doesnt cause damage to your Handy Board, I dont think your motor will be able to draw sufficient current from the motor port to run properly. Rather, you (...) (25 years ago, 26-Jul-99, to lugnet.robotics.handyboard)
|
| |
| | Re: Voice Recognition Hardware
|
|
Try to track down a company called "CoVox". These guys used to have a speech recognition device that ran on the Apple II (6502) that was pretty cool (speaker dependent of course). Also there is a speech recognition chip for use in toys the HM002 or (...) (25 years ago, 26-Jul-99, to lugnet.robotics.handyboard)
|
| |
| | Voice Recognition Hardware
|
|
Greetings All! I was wondering if anybody out there knows of any good, relatively inexpensive, (<$350) Voice recognition hardware that is relatively easily interfaced to the handy board? Thank you very much. -Ryan Meuth (25 years ago, 26-Jul-99, to lugnet.robotics.handyboard)
|
| |
| | Re: Weak Motor
|
|
(...) I remember someone saying a few months ago that if you use a 12 V battery with the HB, then the HB's built-in charging circuit won't work properly, and that 12 V batteries can initially deliver up to about 14 V, which wouldn't be very kind to (...) (25 years ago, 25-Jul-99, to lugnet.robotics.handyboard)
|
| |
| | Re: something is wrong with my handyboard
|
|
I had a similar problem. In my case, the cause was underneath the board. I had not trimmed one of the components leads enough. When I screwing the board into the case the lead eventually pierced one of the wires going to my Nicad pac. My board would (...) (25 years ago, 25-Jul-99, to lugnet.robotics.handyboard)
|
| |
| | Re: HB Serial line speed change
|
|
(...) Note that this will also require that you disable interrupts, and that will mess up your motors. However, it should be possible. --Chuck (25 years ago, 25-Jul-99, to lugnet.robotics.handyboard)
|
