To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.robotics.handyboardOpen lugnet.robotics.handyboard in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / Handy Board / *6434 (-20)
  Robotic Wheelchair in Wall Street Journal
 
Check out today's Wall Street Journal, Page B1, above the fold, for an in depth article with much better photos than on the web site. I'm sure it's on the WSJ web site, too, but I haven't checked. Bill Richman (...) RMT (25 years ago, 1-Jul-99, to lugnet.robotics.handyboard)
 
  Re: Robotic Wheelchair
 
(...) There's an on-line blub about it at: (URL) wild!!! Bill Richman incolor.inetnebr.com/bill_r (Home of the COSMAC Elf microcomputer simulator!) (25 years ago, 1-Jul-99, to lugnet.robotics.handyboard)
 
  Re: Robotic Wheelchair
 
Is anyone familiar with Fuzzy Logic - 'cause that's how they do it........ (...) (25 years ago, 1-Jul-99, to lugnet.robotics.handyboard)
 
  Re: LM35 Temp Sensor TRICK FOR USE
 
Anybody catch the segment last night on the robotic wheelchair. I think it was on Dateline. Watching it climb stairs was impressive, but seeing the chair stand upright on two of its four wheels while the occupant caught a 25lb sack of lead, all (...) (25 years ago, 1-Jul-99, to lugnet.robotics.handyboard)
 
  Re: Robotic Wheelchair
 
I did see that! Very impressive, as long as you don't run into an object below the CG while up on two wheels :-). They have probably thought of that already. This is the kind of good work that people in robotics can do. There are other "robots" in (...) (25 years ago, 1-Jul-99, to lugnet.robotics.handyboard)
 
  Robotic Wheelchair
 
Anybody catch the segment last night on the robotic wheelchair. I think it was on Dateline. Watching it climb stairs was impressive, but seeing the chair stand upright on two of its four wheels while the occupant caught a 25lb sack of lead, all (...) (25 years ago, 1-Jul-99, to lugnet.robotics.handyboard)
 
  Help needed with bootstrap mode
 
I have a problem getting handy board into bootstrap mode. I'm now in the face six (installing lcd screen and downloadin ic). It worked earlier, but now it just won't go into bootstrap mode. I have tested the switch and traced wires from it to the (...) (25 years ago, 1-Jul-99, to lugnet.robotics.handyboard)
 
  Subject information
 
This is a side issue, I know, but there seems to be a lot of mail recently without a subject. Please try to include a descriptive subject for your posts. (...) (25 years ago, 30-Jun-99, to lugnet.robotics.handyboard)
 
  (no subject)
 
can the 68hc811e2fn be used insead of hc11a1fn? what mods would i have to make? thanks phil (25 years ago, 30-Jun-99, to lugnet.robotics.handyboard)
 
  Re:
 
Fernando: This is not too much information to go by, but here are some thoughts. 1. If you use MS Windows 95/98/NT hbdl is your best bet as a downloader, since dl or dlm hang up under these OS's, even in a MSDOS terminal window. dl and dlm work (...) (25 years ago, 30-Jun-99, to lugnet.robotics.handyboard)
 
  (no subject)
 
We had been building a handyboard(hb) but we have severe problems, We download the buffalo using the hbdl windows downloader (dl indicates a serial timeout, dlm just hangs up). When Buffalo is succesfully loaded (it sometimes halts with a error in (...) (25 years ago, 30-Jun-99, to lugnet.robotics.handyboard)
 
  Re: Moving Straight
 
So far nobody has mentioned using a compass to control the 'bot's heading. (URL) Nick (...) (25 years ago, 29-Jun-99, to lugnet.robotics.handyboard)
 
  RE: LM35 Temp Sensor
 
The output pin of the LM35 gives you the ambient temperature in 10mV/degree C directly. The 47k pullup resistor will form a voltage divider with the output. You either have to do some conversion (complicated) or eliminate the pullup (easy).... Paul (...) (25 years ago, 29-Jun-99, to lugnet.robotics.handyboard)
 
  RE: Moving Straight
 
Our first challenge was to get our robot to move ahead straight. There seemed to be a difference in the motor torques. We used shaft encoders and compared the counts every 200 to 500 milliseconds. Slowing down the motor that had a higher count, for (...) (25 years ago, 29-Jun-99, to lugnet.robotics.handyboard)
 
  RE: Moving Straight
 
Many people use trial and error to come up with a wheel differencial factor that should always be applied so that even without looking at the encoders the robot should move pretty straight. If you do the compensation on the fly that is OK but during (...) (25 years ago, 29-Jun-99, to lugnet.robotics.handyboard)
 
  Re: Moving Straight
 
I use the 9 gram Piezo gyro in my Hand Launch Glider to keep it moving level despite strong wind conditions. Could you use that in your robot as a "Rudder" input? The 9 gram Piezo gyro costs about 9,500 yen here in Japan. That is about $80.00. I (...) (25 years ago, 29-Jun-99, to lugnet.robotics.handyboard)
 
  Re: Quickcams
 
(URL) check these guys out they have done what your thinking... good luck phil (...) (25 years ago, 28-Jun-99, to lugnet.robotics.handyboard)
 
  new address
 
hi all This note is to let you know that Josh Welber has a new email address. In future you should send mail to jaw@duckrabbit.org I will be canceling my interport address as of the 1st. Thanks josh (25 years ago, 28-Jun-99, to lugnet.robotics.handyboard)
 
  H- Bridges
 
Have any of you got some experience with H-bridges? I want to use 2 digital outputs to toggle a motor on/off in 2 directions. Does this sound reasonable? if any of you have a lead on a good web resource, I'd appreciate the URL... K.M. (25 years ago, 28-Jun-99, to lugnet.robotics.handyboard)
 
  Re: Moving Straight
 
Try a differential transmission (assuming you're using Lego parts). (2 URLs) motor drives the bot, with both wheels turning at the same rate. The other turns the bot by changing the relative speed of the wheels. Ross M. Tonkens, M.D. Medical (...) (25 years ago, 28-Jun-99, to lugnet.robotics.handyboard)


Next Page:  5 more | 10 more | 20 more

Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR