 | | Re: Increasing current output to motors on HandyBoard
|
|
Hi, Anyone know where I can purchase a commercial unit that I can operate automobile starter type relays from the COMOS outputs on the handyboard expansion board? only 5 mA per output. Or would it be eaiser to fabricate? I don't want to damage the (...) (25 years ago, 11-Apr-99, to lugnet.robotics.handyboard)
|
| |
| | Re: multitasking
|
|
(...) The subroutines continue execution exactly where they left off, making the multitasking transparent to you. You normally shouldn't have to give any thought to how many ms each one gets. If timing is important to you for some reason and the (...) (25 years ago, 11-Apr-99, to lugnet.robotics.handyboard)
|
| |
| | multitasking
|
|
I have a simple question regarding multitasking. I am using two subroutine in a multitasking. start_process(ir()); start_process(detect()); Both subroutine should run for 5 ms(default). Consider an example that the subroutine detect() require more (...) (25 years ago, 11-Apr-99, to lugnet.robotics.handyboard)
|
| |
| | Re: Increasing current output to motors on HandyBoard
|
|
Total cost for both, $56.00. Smaller ones are cheaper. Again, the advantage is convenience, not cost. These pulg right into the motor driver output ports on either the Handy Board or the Rug Warrior with the L293D left in place, and take no other (...) (25 years ago, 10-Apr-99, to lugnet.robotics.handyboard)
|
| |
| | Re: Quick troubleshooting help please!!!!
|
|
I would also check the circuit traces. Clip an ohm meter to the battery ground and check all the ground points, then do the same for +battery. Take a magnifying glass to the traces you can see. Look for places where the smoke got out. Once the (...) (25 years ago, 10-Apr-99, to lugnet.robotics.handyboard)
|
| |
| | Re: Increasing current output to motors on HandyBoard
|
|
So that's like $28 for the H excluding the protecting circuitry? How much did this setup cost for both motors? ---...--- ericson mar Robotics Consultant mar@cooper.edu (212)353-4356 Department of Mechanical Engineering The Cooper Union for the (...) (25 years ago, 10-Apr-99, to lugnet.robotics.handyboard)
|
| |
| | Re: Increasing current output to motors on HandyBoard
|
|
Howdy, My original suggestion was to use *solid state* relays. They don't have any contacts. I use them plugged right into my Rug Warrior board at the motor output ports (would work the same on my Handy Board, but I have it on a smaller base, and (...) (25 years ago, 10-Apr-99, to lugnet.robotics.handyboard)
|
| |
| | Re: Increasing current output to motors on HandyBoard
|
|
Haven't actually tried it, but I was thinking of the same sort of thing. Use a FET for PWM and a DPDT relay for direction. practically speaking, if you only switched the relay when the FET was off, no power transition, etc.... If your 'bot moves (...) (25 years ago, 10-Apr-99, to lugnet.robotics.handyboard)
|
| |
| | GCC/HC11 small patch
|
|
I contacted the original person who did the HC11 port to gcc (Otto Lind), and he pointed me to a patch for it. If you're using gcc-2.8.1 with the HC11 patches in it, you may want to try this: At line 502 of config/m6811/m6811.c, change from: { (...) (25 years ago, 9-Apr-99, to lugnet.robotics.handyboard)
|
| |
| | Re: GCC 2.8.1 for HC11
|
|
(...) You can have a copy of mine if you like. You can relocate it to any available digital ports with ease. It is set up for a single sensor, but you can easily add as many as you have ports for. (...) For people using the Handy Board in small (...) (25 years ago, 9-Apr-99, to lugnet.robotics.handyboard)
|
