 | | Are GP2D02 available in Australia
|
|
Hi all, Can anybody tell me from where I can get GP2D02 in Australia. Sincerely Javaid Iqbal (26 years ago, 8-Mar-99, to lugnet.robotics.handyboard)
|
| |
| | Re: Sharp GP2D02 code available
|
|
I just finished sending a question to the mail list but may have my problem fixed? Just from blind luck. I have digital out #7no the expansion board and digital in#15 on the main board and the first of the zeros on on the LCD changes to a one at (...) (26 years ago, 8-Mar-99, to lugnet.robotics.handyboard)
|
| |
| | Re: Sharp GP2D02 code available
|
|
Hi Barry, I have a GP2D05 from Acroname Inc., Have wired as per instructions black for gnd., green for Vin, Yellow for Vout, and red for Vcc.The pin outs are different than the GP2D02. Then installed the diode and connectors for the handyboard .as (...) (26 years ago, 8-Mar-99, to lugnet.robotics.handyboard)
|
| |
| | stepper motors
|
|
Hi : I am looking for a stepper motor that works at 7V. I was wondering if any of you have used stepper motors for the handyboard or the Rug Warrior. If so, what model did you use and what was your selection criterion for the motors. Thanks. (26 years ago, 7-Mar-99, to lugnet.robotics.handyboard)
|
| |
| | Re: Where do I get Sharp GD sensors
|
|
I ordered mine from Acroname Inc. for $19.00. They also have sample code provided by Gary Livick. I haven't connected it to the handyboard as or this time but will be intersted to know how everyone else is doing it. Mine is a model GP2D02. Good Luck (...) (26 years ago, 6-Mar-99, to lugnet.robotics.handyboard)
|
| |
| | HB v1.2, IC v3.1 and ir functionality
|
|
I'd like to get the ir functionality working on my v1.2 handy board. I am using the 3.1 version of IC from newton labs. See below for the files included with this release. According to The Handy Board Technical Reference" Dated Jan 16, 1997, I must (...) (26 years ago, 6-Mar-99, to lugnet.robotics.handyboard)
|
| |
| | Re: Rolling Ball Inclinometers
|
|
I recall one of the surplus electronics/mechanics catologs (All Electronics? Herbach&Rademan) were selling them for $0.50 -----Original Message----- From: Michael N Rosenblatt <mr4@andrew.cmu.edu> To: handyboard@media.mit.edu (...) (26 years ago, 6-Mar-99, to lugnet.robotics.handyboard)
|
| |
| | Re: Two servos, one input ?
|
|
(...) Why do you want to have two servos doing exactly the same thing? Why can't you simply mechanically hook up the two things you want to drive the same way to a single servo? (26 years ago, 6-Mar-99, to lugnet.robotics.handyboard)
|
| |
| | Re: Could IR ranging sensors be used with Rug Warrior board as well
|
|
(...) I designed and etched a small adapter board that interfaces three Sharp GPD05 and one GPD02 sensors with RW. It replaces the contact bump switches with the Sharp detectors by driving voltage followers to the level of the resistor ladder used (...) (26 years ago, 5-Mar-99, to lugnet.robotics.handyboard)
|
| |
| | Where do I get Sharp GD sensors
|
|
Thanks for the info. I am decided on sharp, because I want to do wall following, now where do I get them. Also, where do I get some code for it, if there are any? Thanks much. (26 years ago, 5-Mar-99, to lugnet.robotics.handyboard)
|
