 | | Re: Hamamatsu P5587
|
|
I'm not an ASCII artist, so I'll attempt a verbal description. View the P5587 with the emitter/detector side facing you and have two pins on the left and three on the right. In this position pin-1 is in the upper left corner, pin-2 in the lower (...) (26 years ago, 4-Mar-99, to lugnet.robotics.handyboard)
|
| |
| | Hamamatsu P5587
|
|
Does anybody have the pinouts or spec sheet for the Hamamatsu P5587 optical sensor? Thanks (26 years ago, 4-Mar-99, to lugnet.robotics.handyboard)
|
| |
| | Re: Sharp GP2D02 code available
|
|
Thanks Barry, great work. I do have one little question: As I read the data sheet of the GP2D02 ( (URL) ) I saw some timing specifications that i think are not taken care of in your software. Please correct me if I'm wrong. The timing chart shows (...) (26 years ago, 4-Mar-99, to lugnet.robotics.handyboard)
|
| |
| | Re: Precise timing with the Handyboard ?
|
|
(...) Use the TIC port 2 or 3. The precision of the reading you'll get is 0.5 us. About a year ago I posted some drivers to make such measurements. Tell me if you want them. cu Tom -- Thomas Hauri ZHW Zuercher Hochschule Winterthur University of (...) (26 years ago, 4-Mar-99, to lugnet.robotics.handyboard)
|
| |
| | Precise timing with the Handyboard ?
|
|
Hi, does anybody know how to measure the time between two trigger signals as precise as possible ( around 10 microseconds would be fine.) with the handyboard. Peter -- Dr. Peter Borrmann University of Oldenburg Phone: +49 441 798 3362 (office) (...) (26 years ago, 4-Mar-99, to lugnet.robotics.handyboard)
|
| |
| | Re: Psion Electronic Organizer
|
|
(...) I would like to know the same thing of the PalmIII. (...) ---...--- Shoot-to-Win Protect the 2nd Amendment ---...--- (26 years ago, 4-Mar-99, to lugnet.robotics.handyboard)
|
| |
| | Psion Electronic Organizer
|
|
Did anybody hook up a handyboard to a Psion Electronic Organizer? Maybe via IrDA interface or serial cable? Alf (26 years ago, 4-Mar-99, to lugnet.robotics.handyboard)
|
| |
| | 3 used HB
|
|
I am receiving several answers. Tonight I plan to take some digital pictures of what I have and answer to the e-mails that I have received. I am located in Metro Detroit , Mi, USA. I would like to charge 150 US $ per HB + shipping (should be between (...) (26 years ago, 3-Mar-99, to lugnet.robotics.handyboard)
|
| |
| | Sharp GP2D02 code available
|
|
Hi, I just posted a short tutorial and software to use the Sharp GP2D02 infrared ranging sensor with the Handy Board. This sensor is very small, relatively cheap (about $21) and gives an accurate distance reading for objects that are between 10cm (...) (26 years ago, 3-Mar-99, to lugnet.robotics.handyboard)
|
| |
| | Re: Skiff board?
|
|
I think it's going to be a Compaq product, actually. It definitely won't be released with the free licensing policy of the Handy Board. It was developed by Compaq and with the support of an MIT student who works for them. From what I know, the main (...) (26 years ago, 3-Mar-99, to lugnet.robotics.handyboard)
|
| |
| | Re: Skiff board?
|
|
No, no Skiffs are available until this summer, at the earliest. I jkust tried over the past month to procure one from the Cambridge Research Lab for a project in the AI Lab here and all to no avail... (Hence the Handy Board). gms (26 years ago, 3-Mar-99, to lugnet.robotics.handyboard)
|
| |
| | Re: Skiff board?
|
|
(...) Neat, but it doesn't look like the design is being released. Any way to get one of these? Thanks, Duncan (26 years ago, 3-Mar-99, to lugnet.robotics.handyboard)
|
| |
| | 3 used HB
|
|
I have 3 Gleason Research Handyboard for PC (GRHB-PC) that I would like to sell for half price or less. Mint conditions , I still have all the boxes. I have finished my project succesfully. Does anybody have a suggestion where to sell used (...) (26 years ago, 3-Mar-99, to lugnet.robotics.handyboard)
|
| |
| | Re: Java and 68hc11
|
|
The Skiff board actually built around a 200 mhz StrongARM processor (acquired from DEC). Fred In your message you said: (...) (26 years ago, 3-Mar-99, to lugnet.robotics.handyboard)
|
| |
| | Re: Java and 68hc11 (Skiff)
|
|
Actually, the Skiff uses a StrongARM SA110 processor. The board was used this year by MIT's 6.270 robotics course in place of the 6811 design. I haven't heard how the new design worked out. Maybe someone on this list has some details (?) - Brian (...) (26 years ago, 3-Mar-99, to lugnet.robotics.handyboard)
|
| |
| | Re: Where to buy handyboard PCB
|
|
(...) (26 years ago, 3-Mar-99, to lugnet.robotics.handyboard)
|
| |
| | Re: Java and 68hc11
|
|
Interesting ! Another cool site is (URL) a JVM for the 68hc11 can be downloaded with all the instructions about it If someone of you likes Java, this can be quite nice. Bye Stefano ---...--- (...) on (...) (26 years ago, 3-Mar-99, to lugnet.robotics.handyboard)
|
| |
| | Re: Java and 68hc11
|
|
Check-out the Skiff project at : (URL) seem to be using Java on a 68hc11 board. (26 years ago, 3-Mar-99, to lugnet.robotics.handyboard)
|
| |
| | Re: Stepper Motors
|
|
I purchase the motors from Jameco. I connected the stepper motors on the motor headers. From left to right ( left meaning next to the RJ jack ) in this sequence: Brown, Skip,Red,Blue,Skip,Yellow. What do you mean by the pattern in the LED's ? (...) (26 years ago, 3-Mar-99, to lugnet.robotics.handyboard)
|
| |
| | Java and 68hc11
|
|
Hi, do anyone know something interesting about java virtual machine porting on 68hc11? And do you know if is it possible to write some high level code for the controller using Java ? (Maybe for some low level routines c is needed). (26 years ago, 3-Mar-99, to lugnet.robotics.handyboard)
|
