 | | expansion board - servo control
|
|
Hi, I stopped working with the handyboard for a while but just started back up again. I put the expansion board onto my handyboard and began testing it. After testing the general tests done before with just the handyboard I started testing the servo (...) (27 years ago, 21-Dec-98, to lugnet.robotics.handyboard)
|
| |
| | unable to download P_code
|
|
Hi everybody, When the one end of the RJ11 cable plug into the RJ12 side entry(J10), it supposed the red LED on the charger board will light up. However, it failed to light up. Hence, this made the booststrap failed and I unable to download the (...) (27 years ago, 21-Dec-98, to lugnet.robotics.handyboard)
|
| |
| | FW: change of address
|
|
-----Original Message----- From: Jaron Paludanus [mailto:j.paludanus@....a2000.nl] Sent: donderdag 17 december 1998 23:58 To: Fred G Martin Subject: change of address I'm not sure my previous mail came through but I have gone high-speed by cable (...) (27 years ago, 21-Dec-98, to lugnet.robotics.handyboard)
|
| |
| | Unable to download P_code
|
|
Hi everybody, When the one end of the RJ11 cable plug into the RJ12 side entry(J10), it supposed the red LED on the charger board will light up. However, it failed to light up. Hence, this made the booststrap failed and I unable to download the (...) (27 years ago, 21-Dec-98, to lugnet.robotics.handyboard)
|
| |
| | Help Needed -Reply
|
|
You don't need to put that code into eeprom. Just put the code inside a main() function block like this: void main(void) { YOUR CODE } Be sure and include the start button logic at the start of your code. The handyboard with start and automaticly (...) (27 years ago, 21-Dec-98, to lugnet.robotics.handyboard)
|
| |
| | I need a poloroid sonar board pinout.
|
|
I got a hold of a Poloroid OneStep Sonar camera at the second hand store, but it does not seem to match any of the pinouts I've seen on the Web... I've aready seen the pinout at WIRZ, but it is not the same. this board has 16 pins all at the edge of (...) (27 years ago, 20-Dec-98, to lugnet.robotics.handyboard)
|
| |
| | Re: Help Needed
|
|
Ever tried making a main() function? I don't have a handyboard yet, but I think it runs without the connection... See you, Cesar (27 years ago, 20-Dec-98, to lugnet.robotics.handyboard)
|
| |
| | Help Needed
|
|
Hi I have an IC program (c text format), and I want to download this program to the eeprom of the handyboard and run it without having connection with the host PC (remove the phone cable) and use the start button to run. How I can convert my c file (...) (27 years ago, 20-Dec-98, to lugnet.robotics.handyboard)
|
| |
| | Re: stepper motors from 5 1/4 drives
|
|
Hi! (...) okay, another newbie reply :-) After I received this message I opened several 5 1/4 drives that were going to trash at my job and took all the stepper motors and integrated circuits. Here's what I figured out: 1 - All the stepper motors I (...) (27 years ago, 20-Dec-98, to lugnet.robotics.handyboard)
|
| |
| | Re: a/d range
|
|
Hi friends! Thank you for the replies about this topic. Now I could get a Reference Manual too... The a/d range is determined by the references given to the VrefH and VrefL pins. But be careful about this: "There should be at least 2.5V between (...) (27 years ago, 20-Dec-98, to lugnet.robotics.handyboard)
|
