 | | dc motor output control
|
|
hi everyone, i need some help on controling the output voltage of the dc motor ports. the output voltage is 9.6V and i like to know if there is any way to clamp down the voltage to 5V or lesser. i try using a enternal resistor but the output signal (...) (26 years ago, 18-Dec-98, to lugnet.robotics.handyboard)
|
| |
| | Re: Downloader and a/d
|
|
Cesar, (...) According to my book, you can set the reference voltages to anything from Vss to Vss + 6.0 V (notice that this is higher than Vdd). The A/D result is a ratioatic comparison for the sample voltage to the references. Page 48 of the (...) (26 years ago, 18-Dec-98, to lugnet.robotics.handyboard)
|
| |
| | Replacing L293D with L298H
|
|
Hi Fred and others, I very desperate to debug the problem that took place in my HD. When I download the P_code, it is successfully downloaded. However, when the next instruction ask to reset the board, no words of sentence appear on the LCD. Only 16 (...) (26 years ago, 18-Dec-98, to lugnet.robotics.handyboard)
|
| |
| | Downloader and a/d
|
|
Hi friends! First thank you a lot for the advices on the FingerBoard. It really gets near to what I need, but that ram chip is another headake. So I believe more in a "light" version of the Handyboard right now, later I'll make a specific version (...) (26 years ago, 18-Dec-98, to lugnet.robotics.handyboard)
|
| |
| | Re: HD LCD problems
|
|
(...) On a lark, I'll suggest that perhaps U6 is damaged. If you have another 74HC138 around, try swapping it for the one on your HB. I had a "similar" problem (although not identical) and was able to diagnose the 74HC138 as the problem. I too was (...) (26 years ago, 17-Dec-98, to lugnet.robotics.handyboard)
|
| |
| | RE: Hot serial interface board
|
|
<<snip>> So here's my question. Does your serial interface board run hot, i.e. noticeably hot to the touch. On my serial interface board (version 1.1 as printed on the board) the white ceramic block gets very hot along with the power chip? in the (...) (26 years ago, 16-Dec-98, to lugnet.robotics.handyboard)
|
| |
| | A Poloroid Sonar question.
|
|
I've got a poloroid sonar question. I got a hold of a Poloroid OneStep Sonar camera at the second hand store, but it does not seem to match any of the pinouts I've seen on the Web... This board has 16pins, I believe this board is manufactured by TI. (...) (26 years ago, 16-Dec-98, to lugnet.robotics.handyboard)
|
| |
| | Re: Mapping
|
|
Thanks for the tip on reflection error. I'll have to build in a function to weight the position accordingly. I'm trying to stay away from occupency grids and use the native vectors to conserve memory while maintaining accuracy. I may have to resort (...) (26 years ago, 16-Dec-98, to lugnet.robotics.handyboard)
|
| |
| | HD LCD problems
|
|
Hi FThompson, Fred and other, I encountered some problem in the downloading. I was successfully able to download the p_code into the HD. However, When the instruction proned me to reset the board,it always appears on the LCD without any lettering (...) (26 years ago, 16-Dec-98, to lugnet.robotics.handyboard)
|
| |
| | Re: Beginner's Help
|
|
(...) I've never hot HBDL to work, and I've tried it on a 386 (laptop), 486 and Pentium. Don't know why: just won't work under win3.11 win95 or win98. The DOS one I've used with quite a bit of success. Make sure you are restarting the computer (ie, (...) (26 years ago, 16-Dec-98, to lugnet.robotics.handyboard)
|
