 | | Re: start_process() questions
|
|
(...) Yes. The subroutine acts just like any other function that you call. (...) Once you do a start_process, that subroutine will run indepently and concurrently with your main program. It does not "run out of time"... it will continue to run until (...) (28 years ago, 8-Dec-98, to lugnet.robotics.handyboard)
|
| |
| | Re: two way radio question and data link
|
|
Details on Radio Data Modules as follows: I have called ABACOM Technologies --new phone # (416) 236 3858) and this is probably your best bet for voice or data use. Data & prices are from Circuit Cellar Ink magazine TRANSMITTER * 30 x 10 x 5mm * (...) (28 years ago, 7-Dec-98, to lugnet.robotics.handyboard)
|
| |
| | start_process() questions
|
|
Hi, I'm using start_process() to run a set of processes. My questions() are: 1. does start_process() re-initailize all the called process's (local) variables every time it calls the process? 2. If the process does not complete before its alloted (...) (28 years ago, 7-Dec-98, to lugnet.robotics.handyboard)
|
| |
| | SPO 256
|
|
F.Y.I. B.G. Micro no longer is selling the Text to speech IC "CTS256A-AL2" they only have the SPO256 IC in stock. This was confirmed by B.G. Micro on 12/07/98. According to a few people they still sold them as pairs as of 08/98 If anybody else is (...) (28 years ago, 7-Dec-98, to lugnet.robotics.handyboard)
|
| |
| | spo256 -Reply
|
|
I bought both from B.G. Micro. (They were not selling the 3.12MHz crystal, however, I successfully used a slightly faster (3.26??) clock. I assume the pitch of the voice was a little higher but it worked. -Drew (...) Does anyone know who sell's the (...) (28 years ago, 7-Dec-98, to lugnet.robotics.handyboard)
|
| |
| | Re: spo256
|
|
www.bgmicro.com about $5 or so for the chip ??? (28 years ago, 7-Dec-98, to lugnet.robotics.handyboard)
|
| |
| | re: www."hc11"
|
|
wsomebody sent a list of www.'s from different source code for HC11 by mistake I erased please release then again thankx (28 years ago, 7-Dec-98, to lugnet.robotics.handyboard)
|
| |
| | communication problem
|
|
Hi everybody I seek someone who can help me. I use handy board and xc40 board(it mounts xc4010 FPGA chip). And I have to make two board communicate each other. But there is a problem that I don't know the method. In handy board's F&Q page, It says (...) (28 years ago, 7-Dec-98, to lugnet.robotics.handyboard)
|
| |
| | Re: Extra output for clocking (Using Hardware Output Compare)
|
|
Hugo: I am not going to be able to answer this one fully. We will need to hear from others on the list to hear how to mix assembler code into an IC program, how to have the IC program modify assembler variables, and how to set up interrupt service (...) (28 years ago, 7-Dec-98, to lugnet.robotics.handyboard)
|
| |
| | communication between two boards
|
|
I use handy board and xc40 board(It has xc4010 FPGA chip) The problem is that they must communicate each other. But I don't know how I can make them communicate. In Q&A(at mit's handy board home page) it says that SPI pin can be used as digital (...) (28 years ago, 7-Dec-98, to lugnet.robotics.handyboard)
|
