 | | Re: Has anyone been experimenting with mapping algorithms?
|
|
(...) The two basic approaches are (1) a bitmap, and (2) a list of obstacle coordinates. A bitmap is just a grid of 1's and 0's indicating the presence of an obstacle at each grid point. It can be implemented as a 1-D integer array with a simple (...) (26 years ago, 29-Nov-98, to lugnet.robotics.handyboard)
|
| |
| | Has anyone been experimenting with mapping algorithms?
|
|
Hi everyone, We've been reading up on the many different algorithms for mapping an environment using autonomous robots. Has anyone else been trying to figure out the best approach to map an area and it's obstacles using less than 32k of memory? (26 years ago, 28-Nov-98, to lugnet.robotics.handyboard)
|
| |
| | Re: Choosing a shaft encoder?
|
|
We're using a track drive system and we're going to be using L.E.D. proximity sensors off of the teeth of the track gears. The tank tracks appear to be very stable but it's still too early in the development to know how repeatable the robot (...) (26 years ago, 28-Nov-98, to lugnet.robotics.handyboard)
|
| |
| | Re: Optrex lcd displays
|
|
I must apologize for my last request, upon further investigation I found an excellent resource that answers the questions i posed earlier. For anyone who might be interested, the source can be found at : LCD MODULE TECHNICAL REFERENCE (FAQ) Version (...) (26 years ago, 28-Nov-98, to lugnet.robotics.handyboard)
|
| |
| | Re: Choosing a shaft encoder?
|
|
i use US Digital encoders, www.usdigital.com. they are a bit costly, but very accurate, and have quite a few numbers of resolutions. good luck justin (26 years ago, 28-Nov-98, to lugnet.robotics.handyboard)
|
| |
| | Optrex lcd displays
|
|
I am trying to interface an Optrex DMC display to a miniboard. What pins besides the data lines need to be connected and to what? Anyone used these displays yet, I have two a one line x 16 characters and a two line x 16 characters. The pin out (...) (26 years ago, 28-Nov-98, to lugnet.robotics.handyboard)
|
| |
| | Re: Choosing a shaft encoder?
|
|
(...) hy, I used HewlettPackard shaft encoders HEDL5540 (500 steps per revoltion) with HCTL2020 quadrature shaft counters/decoders. With them you get 500*4=2000 steps per revolution, which is quite a lot. For me They seem to be a good (but not (...) (26 years ago, 28-Nov-98, to lugnet.robotics.handyboard)
|
| |
| | Re: Choosing a shaft encoder?
|
|
(...) I've had good results using the Hall-effect magnetic sensors that Patrick Hui sent with my HandyBoard. I glued magnets into three of the six holes in a Lego pulley wheel and glued the sensor into a small Lego brick. I don't know the part (...) (26 years ago, 28-Nov-98, to lugnet.robotics.handyboard)
|
| |
| | Re: How to use the addition analog port ?
|
|
You can time share both your digital and your analog so long as your signal update speeds are not critical. Use a 4 to 8 demultiplexing chip for 4 of your digital I/O and an 8 to 4 multiplexer for the other 4. This effectively provides 8 digital (...) (26 years ago, 28-Nov-98, to lugnet.robotics.handyboard)
|
| |
| | When people answer a question, I would like to broaden my knowledge as well.
|
|
Please either carbon copy your solutions to me, or the HB mailing list. I see a lot of good questions, but only a very few peoples responses. Thank you, (26 years ago, 28-Nov-98, to lugnet.robotics.handyboard)
|
