 | | Optrex lcd displays
|
|
I am trying to interface an Optrex DMC display to a miniboard. What pins besides the data lines need to be connected and to what? Anyone used these displays yet, I have two a one line x 16 characters and a two line x 16 characters. The pin out (...) (26 years ago, 28-Nov-98, to lugnet.robotics.handyboard)
|
| |
| | Re: Choosing a shaft encoder?
|
|
(...) hy, I used HewlettPackard shaft encoders HEDL5540 (500 steps per revoltion) with HCTL2020 quadrature shaft counters/decoders. With them you get 500*4=2000 steps per revolution, which is quite a lot. For me They seem to be a good (but not (...) (26 years ago, 28-Nov-98, to lugnet.robotics.handyboard)
|
| |
| | Re: Choosing a shaft encoder?
|
|
(...) I've had good results using the Hall-effect magnetic sensors that Patrick Hui sent with my HandyBoard. I glued magnets into three of the six holes in a Lego pulley wheel and glued the sensor into a small Lego brick. I don't know the part (...) (26 years ago, 28-Nov-98, to lugnet.robotics.handyboard)
|
| |
| | Re: How to use the addition analog port ?
|
|
You can time share both your digital and your analog so long as your signal update speeds are not critical. Use a 4 to 8 demultiplexing chip for 4 of your digital I/O and an 8 to 4 multiplexer for the other 4. This effectively provides 8 digital (...) (26 years ago, 28-Nov-98, to lugnet.robotics.handyboard)
|
| |
| | When people answer a question, I would like to broaden my knowledge as well.
|
|
Please either carbon copy your solutions to me, or the HB mailing list. I see a lot of good questions, but only a very few peoples responses. Thank you, (26 years ago, 28-Nov-98, to lugnet.robotics.handyboard)
|
| |
| | Choosing a shaft encoder?
|
|
As a neophyte robot builder and HandBoard user, may I ask for help in choosing the best shaft encoder? What vendor/supplier should I use? The current project is a very simple robot with a goal of accurate navigation. Thanks! (26 years ago, 28-Nov-98, to lugnet.robotics.handyboard)
|
| |
| | Re: How to use the addition analog port ?
|
|
these aren't actually additional ports. if you look at the PCB wiring you'll see that they're just connected to regular inputs 0-3. these extra connectors will be used by the expansion board. please look for an official notice regarding the exp (...) (26 years ago, 28-Nov-98, to lugnet.robotics.handyboard)
|
| |
| | Print to host computer
|
|
Hi, Does anyone know how to print messages to the host computer while running IC.exe using "printf" statement. Currently, when printf is executed, it print to the LCD. Is it true that the handy board can only work when the LCD is plugged onto the (...) (26 years ago, 27-Nov-98, to lugnet.robotics.handyboard)
|
| |
| | How to use the addition analog port ?
|
|
Hi, I need additional port for the analog input. I have used up 7 analog ports and 9 digital ports. Hence, I need additional port from the HD. I came to know that there are 4 extra analog port on the HD just above the analog port 0 to 3. These (...) (26 years ago, 27-Nov-98, to lugnet.robotics.handyboard)
|
| |
| | IC source compilation under DOS
|
|
Hi ALL Here is a Good News. I used Visual c++ successfully to compile IC Source code. I am testing it now. Once it is done I will release the project files/modified files to all. Prasad (26 years ago, 27-Nov-98, to lugnet.robotics.handyboard)
|
