 | | Stepper motors
|
|
Hello, Does anyone have information on how to run a stepper motor using the Handy Board? Any information you can provide would be appreciated. Mario Garcia (28 years ago, 12-Aug-98, to lugnet.robotics.handyboard)
|
| |
| | Re: Some robot pictures
|
|
Cool robots, Chuck! I was wondering it when they were created. It looks like the top one was created first and the last is the bottom one. Is that so? ---...--- ericson mar Master of Engineering Candidate Project: Mobile Robotics mar@cooper.edu (...) (28 years ago, 12-Aug-98, to lugnet.robotics.handyboard)
|
| |
| | Re: serial library for C++
|
|
Check out this site. It works well. The only problem I had was timing issues when trying to read and write to the port too quickly. (URL) Message----- From: Mark Wallace <mawalla3@vt.edu> To: Handyboard@media.mit.edu <Handyboard@media.mit.edu> (...) (28 years ago, 12-Aug-98, to lugnet.robotics.handyboard)
|
| |
| | serial library for C++
|
|
Hello, I have a handy board with poloroid transducers and I am trying use the results of my distance measurments in a C++ program on the computer. I have found programs on the handyboard web page that should alow the handyboard to transmit (...) (28 years ago, 12-Aug-98, to lugnet.robotics.handyboard)
|
| |
| | PID implementation
|
|
Problem: I have built a small robot with differential drive using 3+ACI- diam whee ls turning at 66 RPM +AEA- full power PWM no load. Each wheel has a 16 pulses per rev. reflective type shaft encoder. the robot is controlled by the Handy Board (...) (28 years ago, 12-Aug-98, to lugnet.robotics.handyboard)
|
| |
| | intel hex file
|
|
Hello all, Does anybody has information of the intel hex file. I do understand the intel hex file (xxx.hex) that is generated by the asm programs, but i use a new assembler, (with the gcc compiler) and it generates different intel hex file (...) (28 years ago, 12-Aug-98, to lugnet.robotics.handyboard)
|
| |
| | PCB
|
|
fthompson wrote: "Some time ago Karl Lundt included in his Amateur Robotics column a short description of a new Printed Circuit Fabrication material where you ran the copper clad through a laser printer (to print directly onto the copper rather than (...) (28 years ago, 11-Aug-98, to lugnet.robotics.handyboard)
|
| |
| | Re: mmu
|
|
It's not impossible. The easiest way is to use the same technique as Java (or IC) and write an embedded interpreter that executes code for a "psuedo" machine. The resulting machine can have arbitrarily strict access restrictions between tasks. You (...) (28 years ago, 11-Aug-98, to lugnet.robotics.handyboard)
|
| |
| | PCB Fabrication material.
|
|
Some time ago Karl Lundt included in his Amateur Robotics column a short description of a new Printed Circuit Fabrication material where you ran the copper clad through a laser printer (to print directly onto the copper rather than using iron on (...) (28 years ago, 11-Aug-98, to lugnet.robotics.handyboard)
|
| |
| | Re: General use PCB
|
|
Ed: In a message dated 98-08-05 11:51:18 EDT, you write: << We have been using the Radio Shack, Archer board #276-162A. Specifications: Dimensions 3 inches x 4 inches, with copper lands on one side. 30 holes by 25 holes with mounting holes at 2.5 (...) (28 years ago, 11-Aug-98, to lugnet.robotics.handyboard)
|
