 | | dvice on the algorithm
|
|
Hello, I need some help to go on in my project. The following are the question needed to be answered : 1) Presently, I'm writing a program using Interactive C in my project. The project is involved a robot which has to be mobiled and move from one (...) (26 years ago, 14-Jul-98, to lugnet.robotics.handyboard)
|
| |
| | Please advice on the alogorithm
|
|
Hello, I need some help to go on in my project. The following are the question needed to be answered : 1) Presently, I'm writing a program using Interactive C in my project. The project is involved a robot which has to be mobiled and move from one (...) (26 years ago, 13-Jul-98, to lugnet.robotics.handyboard)
|
| |
| | communicating with the Scott Edwards SSC's
|
|
Hi all, There is a 9600 baud driver for easy control of the Scott Edwards Serial Servo Controller. Please see (URL) and look for the link, "9600 baud serial output." Yours, Fred (26 years ago, 12-Jul-98, to lugnet.robotics.handyboard)
|
| |
| | PLAIN TEXT ONLY
|
|
Dear all, I would like to remind everyone to please attempt to send PLAIN TEXT ONLY messages when you post to the Handy Board mailing list. This is to respect the many of us who have old fashioned text only mail readers, and to save bandwidth in the (...) (26 years ago, 12-Jul-98, to lugnet.robotics.handyboard)
|
| |
| | Mini SSC
|
|
Has anyone used their handyboard to talk to Scott Edwards servo controller (the Mini SSC I or II)? I'm about to experiment with this as soon as my 12 servos arrive, and was wondering if anyone could provide any useful insights or code. (26 years ago, 12-Jul-98, to lugnet.robotics.handyboard)
|
| |
| | ASM 96
|
|
Hi, sorry to drift from the point of this mailing list but I have a question for all the 80C196 users out there. Does anyone have ASM 96? I have been searching for it for weeks now, without any luck. The only thing I can find about it is updates to (...) (26 years ago, 10-Jul-98, to lugnet.robotics.handyboard)
|
| |
| | Re: assembler
|
|
Hi all, Would be great if messages were sent in plain ASCII... Andre Ramos (26 years ago, 10-Jul-98, to lugnet.robotics.handyboard)
|
| |
| | Re: assembler
|
|
Hi Richard, Sorry for my bad english (normaly i speek german). The 68hc11 has differnt kinds of addressing-modes. 1) LDAA #65 : immediate adress, The value is stored in accumulator 2) LDAA result : direct Adress The value from adress RESULT is (...) (26 years ago, 10-Jul-98, to lugnet.robotics.handyboard)
|
| |
| | assembler
|
|
Hello, can anyone tel me the function of the # in the AS11 assembler, i'm new at assembler programming and get sometimes confused about the usage of the # # means a number, but what's the difference between: ldaa #$1000 and ldaa $1000 Thanks, (26 years ago, 10-Jul-98, to lugnet.robotics.handyboard)
|
| |
| | External ram
|
|
Hello all, I have an 68hc11F1 and 32 K of external ram and 32k of flsah. I have the 16 mhz version of the hc11. While having problems to program the flash suggestions from the list where that i probably had a timing problem. So i reduced the (...) (26 years ago, 10-Jul-98, to lugnet.robotics.handyboard)
|
| |
| | Sorry: Re: Inclinometer for Handyboard
|
|
I humbly apologize for the time and bandwidth I forced on everyone with my intended-to-be-small...-and-dirty sketch on the inclinometer. I honestly did not realize the size of the file when I sent it or I'd have found a much better way of doing so. (...) (26 years ago, 10-Jul-98, to lugnet.robotics.handyboard)
|
| |
| | Re: check_sensors.c
|
|
Hi Joe&David,All, Let me explain what I would like my handyboard to do. Guide a lawnmower by detecting the border of cut and uncut grass. Monitor a row of 16 +or- ir emitter/detector pairs placed about every two inches to report to the motor control (...) (26 years ago, 10-Jul-98, to lugnet.robotics.handyboard)
|
| |
| | IR, bitmapping
|
|
I was just wondering if you could get the handyboard to transmit other than just in 125 hz or 100hz. Also...has anyone done anything like making a robot follow another using the ir transmit? Has anyone had any success using shaft encoders to make (...) (26 years ago, 9-Jul-98, to lugnet.robotics.handyboard)
|
| |
| | Re: Inclinometer for Handyboard
|
|
greetings everyone, this is a reminder to please NOT send 1MB attachments to the list! In the guidelines I sent you when you were subscribed to the list, I stated a limit of 50 KB (that's kilobytes) for any message. Please remember that your message (...) (26 years ago, 9-Jul-98, to lugnet.robotics.handyboard)
|
| |
| | Re: ic help
|
|
Hi LLya, Actually, descriptions of these functions are described in HB manual, at least mine has. peek() returns integer value for the given location passed in as the parameter. For example: value = peek( 0x200); The peek returns the int. value (...) (26 years ago, 9-Jul-98, to lugnet.robotics.handyboard)
|
| |
| | FW: Inclinometer for Handyboard
|
|
(...) (26 years ago, 9-Jul-98, to lugnet.robotics.handyboard)
|
| |
| | RE: Inclinometer for Handyboard
|
|
In the previous message, the word 2-dimensional is incorrect. It should be 2-axis (...) (26 years ago, 9-Jul-98, to lugnet.robotics.handyboard)
|
| |
| | RE: Inclinometer for Handyboard
|
|
You could use the effect of gravity force and a potentiometer (variable resistant) to create such thing. In fact if you use a joystick mechanism (or quadraphonic double-potentiometer volume control in the old day) in upside down position and have a (...) (26 years ago, 9-Jul-98, to lugnet.robotics.handyboard)
|
| |
| | Re: Inclinometer for Handyboard
|
|
(...) (URL) has inclinometers.. dunno how much they run however. -d The box said "Requires Windows 95/NT or better"... So I got Unix. Free the Source. Free your Computer... (3 URLs) (26 years ago, 8-Jul-98, to lugnet.robotics.handyboard)
|
| |
| | Re: ic help
|
|
the addresses must be specified in decimal. Justin D. Gullotta.. , Engineer, Rensselaer Polytechnic Institute. (26 years ago, 8-Jul-98, to lugnet.robotics.handyboard)
|
