 | | RC Systems-speech synthesizers
|
|
Hello All, I'm about to order a speech system from RC. I remember a few months ago this was discused on the list. Could anyone tell me which model would be best for the Handyboard(V8600 or V8601)? Also how difficult it would be to connect it to the (...) (27 years ago, 25-Sep-97, to lugnet.robotics.handyboard)
|
| |
| | Re: Handy Board diagram?
|
|
maybe is it the schematic? (URL) your message you said: (...) (27 years ago, 25-Sep-97, to lugnet.robotics.handyboard)
|
| |
| | Re: Handy Board diagram?
|
|
(...) Actually, no, that's not it. The one I'm looking for identifies every pin on every connector. It also says "V.1.1" in the corner, but there's no URL or author. Ken Bullis kbullis@aimnet.com (27 years ago, 25-Sep-97, to lugnet.robotics.handyboard)
|
| |
| | Re: Handy-Board.
|
|
hi, there are a group of us from the university of Victoria (canada) that have built handy-boards for the purposes of robot control. Currently two of us are taking courses in assembly programming. The boards accept s19 codes readily, but its a pain (...) (27 years ago, 25-Sep-97, to lugnet.robotics.handyboard)
|
| |
| | Re: 68hc11 & z80
|
|
(...) Hello Phil- I have built systems in the past around both CPUs you mentioned. Here is my two cents worth- The Z80 is a very easy processor to understand and work with. You are correct that they are quite cheap these days. They are also very (...) (27 years ago, 25-Sep-97, to lugnet.robotics.handyboard)
|
| |
| | 68hc11 & z80
|
|
hi! This is probably beyond the scope of this group. Please forgive me for it. I merely would like to know a couple of things on this subject: if you know of a better place for me to get some info, I'll go there. Thanks again! My question is this: (...) (27 years ago, 25-Sep-97, to lugnet.robotics.handyboard)
|
| |
| | Handy-Board.
|
|
Hi, My name is Sudeshna and I am a student of Wichita State University, Kansas, pursuing a Bachelor's degree in Electrical Engineering. I'm working with a team of 7 on a project of building a robot for which we are using the handy board. All the (...) (27 years ago, 25-Sep-97, to lugnet.robotics.handyboard)
|
| |
| | bounced undelivered messages
|
|
<bold>Marce writes: </bold><x-quoted>I've received four error messages from</x-quoted> <x-quoted>media.mit.edu. Is this usual?</x-quoted> The last message that I personally sent to the handyboard list returned 8 error messages regarding bounced (...) (27 years ago, 24-Sep-97, to lugnet.robotics.handyboard)
|
| |
| | RE: PORTD WOM Control Bit
|
|
So it can be done!. Thanks. You've been my only answer, but I've received four error messages from media.mit.edu. Is this usual?. Did you receive my message from the HB mailing list? (...) from the HB using the SPI port. Works great. (...) (27 years ago, 24-Sep-97, to lugnet.robotics.handyboard)
|
| |
| | Re: PORTD WOM Control Bit
|
|
(...) yes it is normal to receive errors when posting to the list. here is an excerpt from the 'welcome msg' i send everyone when joining the list: 5. When you send to the list, YOU WILL GET BOUNCES. This is normal, there are always some bad (...) (27 years ago, 24-Sep-97, to lugnet.robotics.handyboard)
|
