 | | Handy Board for sale
|
|
Hey all... I have a handy board kit that I order from gleason research about 3 months ago. I turned it on once to see what I could do, downloaded the sample code, and it has been packed away ever since. I just don't have the time to play around with (...) (27 years ago, 24-Jun-97, to lugnet.robotics.handyboard)
|
| |
| | Help : Using Sonar and Encoders on Digital port 0
|
|
Sorry, for sending this out again, but I am not sure whether everyone got it, my mail server has been down, and I hadn't received any replies so I thought that it may not have not gotten out Cheers Michael To: handyboard @ media.mit.edu @ internet (...) (27 years ago, 24-Jun-97, to lugnet.robotics.handyboard)
|
| |
| | RE: dc generator
|
|
thanks... i suspected that, but i wasn't sure.... i'll have to find something with a bigger shaft though (sounds kinky!!) ---...--- From: Joe Martin Sent: Wednesday, June 25, 1997 8:28 PM To: killkie Subject: Re: dc generator Maybe try a lego motor (...) (27 years ago, 23-Jun-97, to lugnet.robotics.handyboard)
|
| |
| | dc generator
|
|
looking for a small generator that pumps 6-15 volts dc at a shaft speed of 1,000 to 5,000 rpm or 10,000 to 20,000rpm.... 12v is the key... but it is to be driven by a .12ci gas motor with a throtle, so maintaining the voltage will have to be left up (...) (27 years ago, 22-Jun-97, to lugnet.robotics.handyboard)
|
| |
| | Help : Using Sonar and Encoders on Digital port 0
|
|
Hi All, I am a student in Sydney, Australia, and I have successfully got the Polaroid sonar working as well as two quad encoders, however, they both use the digital 0 (rightmose digital pin), has anyone got some code which implements both of these (...) (27 years ago, 22-Jun-97, to lugnet.robotics.handyboard)
|
| |
| | Re: Resistor size
|
|
(...) is >there? I don't think so, but I am not an EE major. No, there isn't any harm in using a 1/4 watt in place of a 1/8 watt resistor. The 1/4 watt can handle more power than the 1/8 watt. It's just that the 1/4 is a little larger physically (...) (27 years ago, 20-Jun-97, to lugnet.robotics.handyboard)
|
| |
| | Substitute processor question
|
|
I was looking at the page (URL) instructions on starting the handy board as I just completed the interface. From the parts list, either the MC68HC11A1FN or the MC68HC11E1FN are acceptable, but on this page, the picture of the handy board has an A0FN (...) (27 years ago, 20-Jun-97, to lugnet.robotics.handyboard)
|
| |
| | Magnetic Card Readers again...
|
|
I have found the code from dave negro, but i'm can make work this with my handy... Nothing more has tried this with interactive C(code in C). ===...=== Obtenga su e-mail GRATUITO para toda la vida en: (URL) (27 years ago, 20-Jun-97, to lugnet.robotics.handyboard)
|
| |
| | Photocell problems
|
|
I was wondering if someone could check out this code. I got it to work w/ just the touch sensors and motors. But I added photocells to it and added the code in for that and now the LCD panel reads....231>Press START after I press start it says... (...) (27 years ago, 19-Jun-97, to lugnet.robotics.handyboard)
|
| |
| | Re: I'm happy !!!
|
|
---...--- (...) use (...) My (...) the (...) (27 years ago, 19-Jun-97, to lugnet.robotics.handyboard)
|
