 | | I miss some nice features in IC 3.1...
|
|
Hi, I'm considering to buy IC 3.1. But when I looked at it's features I fount two nice things to be missing: 1. A build in assembler to create the .icb files 2. An option to compile C code instead of interpreting it. (I saw this very nice feature in (...) (27 years ago, 27-May-97, to lugnet.robotics.handyboard)
|
| |
| | Re: Motors: Please help! Going out of my mind...
|
|
(...) Of all the things in a Robot, motors are in some ways the most difficult to obtain. (...) Both Brevel and Globe make such motors, they typically go for anywhere been $175 each and $500 each. (...) [I'll assume that the above exceeds your (...) (27 years ago, 27-May-97, to lugnet.robotics.handyboard)
|
| |
| | Richard Drushel's improved serial and math libraries
|
|
now on-line. See the HB HP ((2 URLs) for the delay. -Fred (27 years ago, 27-May-97, to lugnet.robotics.handyboard)
|
| |
| | IC 3.1
|
|
Is it possible to receive a trial/shareware version of IC 3.1? I don't what to go through the expense of buying the full version unless I know it will do what I need it to do. Thanks in advance. -Brad (27 years ago, 27-May-97, to lugnet.robotics.handyboard)
|
| |
| | IC 3.1
|
|
(...) Hi Joe, Removing drivers depends a bit on what OS you're actually running. Generally, you'd remove lines from your config.sys or autoexec.bat (on c:\) to remove various drivers, if there are some you don't actually need. Networking software on (...) (27 years ago, 27-May-97, to lugnet.robotics.handyboard)
|
| |
| | Out of memory error
|
|
Randy, Thanks for your help so far, but I have a few questions. How can I remove drivers to get more room. Where can I quickly get a copy of IC 3.1? And how much does it cost? -Joe (...) (27 years ago, 27-May-97, to lugnet.robotics.handyboard)
|
| |
| | Memory problems
|
|
I have been having big problems with the programs that I have been writing for my handy board. I currently have around 1400 lines. I expect to have about 2000 when I'm done. I have many functions called throughout the program and recently have (...) (27 years ago, 27-May-97, to lugnet.robotics.handyboard)
|
| |
| | Out of memory error
|
|
(...) At some point, you may run out of memory on the Handyboard; however, it sounds like IC 2.8 is running out of the 640K DOS-limited memory. You might try removing drivers to get more room in the lower 640K. If you move up to IC 3.1, which is a (...) (27 years ago, 26-May-97, to lugnet.robotics.handyboard)
|
| |
| | Re: clueless programmer
|
|
A very simple program which will exercise the motors in this configuration is listed. The first section will put a message on the LCD then wait until the sopt button is pressed. Once the stop button is sensed, it will turn on the motor in port 0. (...) (27 years ago, 26-May-97, to lugnet.robotics.handyboard)
|
| |
| | TEAC Stepper motor
|
|
Has anyone had any experience driving the stepper motor from a TEAC 5 1/4 in floppy drive with the HB. I have been going through Jones' tutorial on stepper motos and have decided that the motor is a permanent magnet, 4 winding variable reluctance (...) (27 years ago, 26-May-97, to lugnet.robotics.handyboard)
|
