 | | Re: SPI & Vector2x
|
|
(...) Maybe, it'll depend on the flooring. I think re-bar in a concrete floor might affect a compass too close to the floor. Last night I was playing with the compass, and found that passing a screwdriver within about 3 inches would affect the (...) (28 years ago, 7-Mar-97, to lugnet.robotics.handyboard)
|
| |
| | Preprocessor for DOS or Windows or '95?
|
|
Hello, I want to use assembler in conjunction with IC, as described in the handyboard technical reference. Apparently this needs a preprocessor. Does anyone have such a thing, or know how to kludge it, or even what it does so I can try to write (...) (28 years ago, 7-Mar-97, to lugnet.robotics.handyboard)
|
| |
| | Re: Re[2]: phone cord length
|
|
thx for correcting my wording. e.g., instead of saying "half twist" i should say "straight through". anyhow, we agree on the definition of what is a phone cable and what is not a phone cable, we just have a different way of illustrating it. the (...) (28 years ago, 7-Mar-97, to lugnet.robotics.handyboard)
|
| |
| | Breaking
|
|
I was wondering what methods of breaking have been used with handyboard motors. Is it OK just to slam them in reverse for a few milliseconds ? Or will the large current impulse be harmful to the motor and driver chips ? It looks like the breaking (...) (28 years ago, 7-Mar-97, to lugnet.robotics.handyboard)
|
| |
| | Re: Re[2]: phone cord length
|
|
Sorry Fred, but I must respectfully disagree..... Fred G. Martin wrote: (snip) (...) Actually it is phone cords which are the crossover type. Use of a patch- cord tester confirms this. I am not familiar with any RJ11 network cables, but I know that (...) (28 years ago, 7-Mar-97, to lugnet.robotics.handyboard)
|
| |
| | SPI & Vector2x
|
|
The v2x compass sounds like a great unit for keeping a mouse centered in a maze corridor. I am looking for some more info on the SPI header pinout, on the HB, and how to connect the v2x to it. I have also seen some .asm code and was wondering if (...) (28 years ago, 7-Mar-97, to lugnet.robotics.handyboard)
|
| |
| | Servo.lis
|
|
Can anyone tell me what servo.lis has in it. I have the servo.c file but not the lis file. I saw in an earlier email that there was an lis file too. When I load servo.c there are undefined functions. Any help is greatly appreciated. Thanks, Tom (28 years ago, 6-Mar-97, to lugnet.robotics.handyboard)
|
| |
| | Re: 567 design help needed
|
|
(...) (URL) --Chuck McManis (URL) opinions in this message are those of the author. No warranty as to the suitability or accuracy is stated or implied. Use at your own risk. cmcmanis@netcom.com +1.408.524.4805 (28 years ago, 6-Mar-97, to lugnet.robotics.handyboard)
|
| |
| | Re: Vector2x SPI interrupt driven code
|
|
(...) From my experience, the calibration is only needed if you need absolute heading data. Any non-moving metal in the immediate neighborhood will have a constant effect on the readings. I just care about maintaining the current heading (go (...) (28 years ago, 5-Mar-97, to lugnet.robotics.handyboard)
|
| |
| | Serial Line and Stop Switch
|
|
Hello, I am building a handy board for the first time using the Douglas Electronics boards and parts from various sources. I have been following the assembly instructions with great success but now I'm stuck at the end of section 4.4, Serial Line (...) (28 years ago, 5-Mar-97, to lugnet.robotics.handyboard)
|
