| | Zero Page Variables?
|
|
IC gurus, I am trying to port some of my IR routines to IC and I am having trouble. I use some bit operations on variables, but this means that the variables must be in the ZP. I converted the variables to be anywhere in the RAM but then I have to (...) (29 years ago, 29-Feb-96, to lugnet.robotics.handyboard)
|
|
| | Re: Handyboard vs. Botboard 2
|
|
The botboard does not incorporate motor drivers; the Handy Board does. The handy board is smaller, and fits into a commercial plastic enclosure with the battery pack underneath. The botboard has prototype area; the handy board does not. The handy (...) (29 years ago, 29-Feb-96, to lugnet.robotics.handyboard)
|
|
| | Handyboard vs. Botboard 2
|
|
Dear Fred and other handyboarders, This might be a strange question for this group. I am busy making a little robotlike object. As I have several Basic STAMPs laying around, I am making it multiprocessor - however, STAMPs don't have interrupts, (...) (29 years ago, 29-Feb-96, to lugnet.robotics.handyboard)
|
|
| | Best way to capture rising and falling edges?
|
|
Hi, It's me again. If anyone has followed the questions I have been asking, you'll see that I am learning, slowly, how to get an interrupt routine trigger on both rising and falling edges of a PORTA line. After much help from this list and Fred (...) (29 years ago, 28-Feb-96, to lugnet.robotics.handyboard)
|
|
| | Technical support is up to all of us now
|
|
Dear Handy Board Users, I am starting to get hit with e-mail from individuals who are having trouble with their Handy Boards. I don't have the time to help people with assorted technical problems on this kind of basis. Therefore, I would urge all (...) (29 years ago, 28-Feb-96, to lugnet.robotics.handyboard)
|
|
| | IC 3.1 Beta4 occasioanlly hangs up Geoport
|
|
Fred, Randy: I noticed that when I use IC 3.1 B4 while I am online (Power MAC 7100/66, Geoport, MACPPP connection) it hangs up (occasionally) the line. It mostly happens if Netscape was used prior to IC invocation. Couple of time it happened in (...) (29 years ago, 23-Feb-96, to lugnet.robotics.handyboard)
|
|
| | RE: motor control
|
|
There is no recommended way. I've got a pretty simple bipolar H-bridge design that you can connect up pretty easily using an opto isolator and get 3 - 6amps of control and software compatibility. Unfortunately I'm not in the kit business nor do I (...) (29 years ago, 23-Feb-96, to lugnet.robotics.handyboard)
|
|
| | Re: Weird LCD problems
|
|
Fred, (et al) Actually I did test to make sure that the LCD was receiving the signal. And indeed it was. I did this before I posted and thought I made it clear. So I guess my problem should have been directed elsewehere since it is not entirely HB (...) (29 years ago, 22-Feb-96, to lugnet.robotics.handyboard)
|
|
| | motor control
|
|
What is the recommended method for connecting motors that draw over 1Amp. to the L293D chips?? Can this be done at all? -SB (29 years ago, 22-Feb-96, to lugnet.robotics.handyboard)
|
|
| | Re: Weird LCD problems
|
|
David -- Soldering d0 to +5v certainly can't help; it should be connected to the data bus (pin 9 of the 6811, pin 11 of the RAM, and pin 3 of the 'hc373). (see the cpu and mem schematic). With board power off, check continuity among these (...) (29 years ago, 22-Feb-96, to lugnet.robotics.handyboard)
|