|
| |
|   sensor (score: 0.501) |
|
| |
|   sensor (score: 0.501) |
|
| |
|   sensor (score: 0.501) |
|
 | | Re: Autonomous Robot
|
| in article 3991FAAF.A8D0FDBA@airmail.net, Steve Baker at lego-robotics@crynwr.com wrote on 8/9/00 5:43 PM: (...) <snip> (...) You can handle this two ways. 1) omnidirectional laser sensor with cylindrical cross-section, which always has the same (...) (26 years ago, 10-Aug-00, to lugnet.robotics)
| |
|   sensor, sensors (score: 0.500) |
|
 | | Re: IR-based proximity measurement
|
| (...) You're welcome - it's a fun problem. At least partially because it's one of the few times I've had to worry about the speed of bytecode execution under the standard firmware (see below). (...) Given what you are transmitting and how you are (...) (20 years ago, 11-Jun-06, to lugnet.robotics.rcx.nqc)
| |
|   sensor (score: 0.500) |
|
 | | Re: Autonomous Robot
|
| in article 398F84B6.F9AE89A8@airmail.net, Steve Baker at lego-robotics@crynwr.com wrote on 8/7/00 8:55 PM: (...) Of course, if odometry puts you inside the circle, you don't need bar codes because you already know where you are! (...) True, and I (...) (26 years ago, 9-Aug-00, to lugnet.robotics)
| |
|   sensor, sensors (score: 0.500) |
|
 | | Re: Stereo Vision
|
| Yup :) I thought of, *after dealing with the mono vision*, going for a stereo approach, because this is one way of dealing with distance measuring, or at least, better object evaluation/recognition. At first I thought of using two USB cams, but (...) (26 years ago, 10-Aug-00, to lugnet.robotics)
| |
|   sensor, sensors (score: 0.500) |
|
 | | Re: Autonomous Robot
|
| in article FyyAqy.5zy@lugnet.com, Ian Warfield at ipw47@hotmail.com wrote on 8/7/00 6:56 PM: (...) That's what this is all about, after all. Type on! (...) There are two ways to design a laser sensor - directional or omnidirectional. Either way (...) (26 years ago, 9-Aug-00, to lugnet.robotics)
| |
|   sensor, sensors (score: 0.500) |
|
 | | Re: Autonomous Robot
|
| in article 398D9DA5.300D416C@airmail.net, Steve Baker at lego-robotics@crynwr.com wrote on 8/6/00 10:17 AM: (...) <regretfully snipped excellent discussion of using line following to find bar codes for landmark recognition> It would be nifty if you (...) (26 years ago, 8-Aug-00, to lugnet.robotics)
| |
|   sensor, sensors (score: 0.500) |
|
 | | Re: NXT electronic additions
|
| (...) That's a better idea because a yellow LED is just a red and a green LED that are both turned on at the same time. Hence there is no additional information in terms of reflectivity than you would have gained from the red and green LED's used (...) (20 years ago, 11-Jun-06, to lugnet.robotics)
| |
|   sensor (score: 0.500) |
|
 | | Re: Newbie needs Help
|
| You only need one rotation sensor and some fancy gearing. Using a differential in a way similar to the "South Facing Cart" or the stearing drive in a dual differential setup, you could directly measure the amount of spin between a driven wheel and (...) (20 years ago, 6-Jun-06, to lugnet.robotics)
| |
|   sensor (score: 0.500) |
|
| |
|   sensor, sensors (score: 0.500) |
|
 | | Re: Autonomous Robot
|
| I thought of another possibility for robot coordinate recognition. It's rather unorthodox, however, and requires some special equipment and setup to make it work. Still, in the interest of creative discussion... Building off the base station idea (...) (26 years ago, 8-Aug-00, to lugnet.robotics)
| |
|   sensor, sensors (score: 0.500) |
|
 | | Re: Was: Some brainstorming needed, now...
|
| (...) Woah there. Be careful - if you read the full description: 1) It's not a general purpose machine - the guy only implemented a simple turntable and a system that lowers the turntable at a constant rate as it rotates. All he can make is hollow (...) (22 years ago, 3-May-05, to lugnet.robotics)
| |
|   sensors (score: 0.500) |
|
 | | Re: Ultrasonic sensor interactions
|
| (...) Within the same room - is unlikely to be a problem - but think about two Sumo bots trying to find each other or two robots doing some kind of cooperative tasks in a contest or something...not likely to be so easy I think. (20 years ago, 22-May-06, to lugnet.robotics)
| |
|   sensor (score: 0.500) |
|
 | | Re: Ultrasonic sensor interactions
|
| (...) Wow! That's a lot lower than I'd have expected - at that frequency there is a good risk of harmonics from normal sound interfering with it. (...) Right - 350 meters per second is pretty slow by computer standards. (...) (Not to mention things (...) (20 years ago, 21-May-06, to lugnet.robotics)
| |
|   sensor (score: 0.500) |
|
 | | Re: Ultrasonic sensor interactions
|
| (...) OK, verification done, the voltage is correctly switched to 5V with the touch sensor. I probably programmed a wrong port# ! But clearly the 5V is enough to power the US transducers (probably with reduced range) Philo (20 years ago, 22-May-06, to lugnet.robotics)
| |
|   sensor (score: 0.500) |
|
 | | Re: Thoughts
|
| Hi Andrew, (...) there are actually 3 I/O lines on each sensor port: - 1 legacy sensor A/D with appropriate power supply on the same line. - 2 digital I/O lines, one of which can also be configured as analog in. The remaining lines are 2 GND pins (...) (20 years ago, 19-May-06, to lugnet.robotics)
| |
|   sensor (score: 0.500) |
|
 | | Ultrasonic sensor interactions
|
| Can someone from the MDP comment on how multiple robots using the ultrasonic sensor interact. It is possible to use this sensor reliably when one or more other robots nearby are using theirs? -Tim (20 years ago, 19-May-06, to lugnet.robotics)
| |
|   sensor (score: 0.500) |
|
 | | Re: Autonomous Robot
|
| (...) Clever! ...Food for thought! The only snag I can see is that when the first laser is being acquired, both the tower and the robot have to spin. It might take a LOT of rotations for them both to happen to be pointing in the right direction for (...) (26 years ago, 8-Aug-00, to lugnet.robotics)
| |
|   sensor, sensors (score: 0.500) |