To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / 8111 (+10)
  Re: Homemade LED Bricks
 
David Johnston <lego-robotics@crynwr.com> wrote in message news:LOBBJCENKNHFLCK...inet.ie... (...) I'd say 330 Ohm 1/4 Watt. (27 years ago, 12-Nov-99, to lugnet.robotics)
 
  Re: Homemade LED Bricks
 
(...) Er, 330 ohm may be ok for the usual transistor type circuit where the nominal supply voltage is 5 volt, if my memory has not failed me. It may be a bit low, I think, for the RCX where the nominal voltage is 9 volts which is almost double of 5 (...) (27 years ago, 12-Nov-99, to lugnet.robotics)
 
  Re: Homemade LED Bricks
 
basicly.. it's i*r=v where i = current in amps and r = resistance in ohms and v = voltage in volts.. so.. If we want to find out the resistor's value.. we re arrange it like so.. r = v/i so 10 millamps (typical led current) = .01 Amps.. And at 9 (...) (27 years ago, 12-Nov-99, to lugnet.robotics)
 
  Re: RIS 1.0 to 1.5 software upgrade
 
Hi! I got a RIS 1.0 in October. I called up Lego Consumer affairs to ask for an update kit for $3.95. They said it is only possible if I had bought from S@H. They also say that it is available to only those lego RIS which have a sticker on the box. (...) (27 years ago, 12-Nov-99, to lugnet.robotics)
 
  Re: Homemade LED Bricks
 
grrr.. I flubbed.. instead of r = .01/9 make it r = 9/.01 ----- Original Message ----- From: Keith Miller <kmiller@talon.net> To: <lego-robotics@crynwr.com> Sent: Thursday, November 11, 1999 10:23 PM Subject: Re: Homemade LED Bricks (...) (27 years ago, 12-Nov-99, to lugnet.robotics)
 
  Re: Homemade LED Bricks
 
(...) Thanks for the enlightenment. I remembered it went something like that. But don't you have to allow for the forward voltage drop across the LED, typically 1.6 volt (still from memory)? That is, the voltage should be 9 - 1.6 = 7.4 volts. So the (...) (27 years ago, 12-Nov-99, to lugnet.robotics)
 
  Re: Homemade LED Bricks
 
(...) [snip] The light pipe dohingus in the "Extreme Creatures" add-on, Space Shuttle Technic kit and a few others does this very nicely, it even adds a rotating display to the works. Its one of the few cool things in the Extreme Creatures expansion (...) (27 years ago, 12-Nov-99, to lugnet.robotics)
 
  Re: tracking robot position
 
(...) Thanks for the tip. Right now, however, $99 seems like quite a lot for me. :-) /Vlad (27 years ago, 12-Nov-99, to lugnet.robotics)
 
  Re: tracking robot position
 
(...) Hi! If the mouse ball is placed at a distance from the rotation center of the robot, then it will never get into a situation where it will rotate around its own axis. Of course, the software has to perform some calculations, but it's always a (...) (27 years ago, 12-Nov-99, to lugnet.robotics)
 
  Re: RCX output and Trains
 
(...) [...snip...] (...) both (...) Oh yes, it *IS* compatible. As Chris Osborn wrote this is probably the easier solution. Another reason to get the good old RCX 1.0 with the adapter plug. Mario (URL) (27 years ago, 12-Nov-99, to lugnet.robotics)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR