 | | #8485 is here
|
|
A large box just dropped on me. An #8485 from DYA shopping. I intend to use the RCX to replace the Technic Control Centre that comes with it. Need to take a little respite from pump testing.:-) See you later! -- C S Soh (URL) where air is power (27 years ago, 5-Oct-99, to lugnet.robotics)
|
| |
 | | Re: Lubricating Cylinders
|
|
(...) My reply from Lego just came. It turns out that they are not ready to answer e-mails in the USA. So now I have to call some phone number. Sounds to me like they don't know the answer and are wasting time so they can find out. (27 years ago, 5-Oct-99, to lugnet.robotics)
|
| |
 | | Pneumatic bits and pieces
|
|
Does anyone out there know if there are "T" pieces for the pneumatics stuff, and if so where to get them. They don't get a mention on shop at home, catalog, or Pitsco. Regards, JB (27 years ago, 5-Oct-99, to lugnet.robotics)
|
| |
 | | Re: Pneumatic bits and pieces
|
|
(...) You get 4 'T' pieces in accessory set 5109 with two lengths of tube. Regards John Stormes (27 years ago, 5-Oct-99, to lugnet.robotics)
|
| |
 | | Re: Pneumatic bits and pieces
|
|
(...) Yes, there are 4 of them in service pack 5109 (along with some tubing). Cost is about 4 USD. I don't have the US spares service phone number, but somebody out there can probably tell you. Stuart (27 years ago, 5-Oct-99, to lugnet.robotics)
|
| |
 | | Re: Rotary electrical coupling
|
|
G'Day If you are willing to use 'non-pure Lego' parts, then Radio Shack has a telephone cord 'detangler' that plugs into standard RJ-11 jacks, has 4 conductors, and 360 degree motion. Works rather well, esp. with some contact enhancer for a cleaner (...) (27 years ago, 5-Oct-99, to lugnet.robotics, lugnet.robotics.rcx)
|
| |
 | | Re: Could somebody use this program?
|
|
(...) (URL) think that fits pretty close to your description except for the building block part. Søren (27 years ago, 5-Oct-99, to lugnet.robotics)
|
| |
 | | Re: RCX + C + Windows
|
|
(...) Miguel, It depends on whether you want your programs to run on the RCX (case 1) or on the PC (case 2). Case 1: Try legOS. It uses gcc and a cross assembler to compile C directly to the RCX. It requires that you download alternative firmware. (...) (27 years ago, 5-Oct-99, to lugnet.robotics)
|
| |
 | | RE: Could somebody use this program?
|
|
(...) <snipped description of new environment for RCX/Cybermaster> (...) Michael, I just downloaded mlCAD and find it an excellent bit of software. The rendering of each step is a bit slow unless you turn on wireframes, but that's not so bad. My 7 (...) (27 years ago, 5-Oct-99, to lugnet.robotics)
|
| |
 | | Re: Could somebody use this program?
|
|
Michael, You can program the RCX and CyberMaster with quite many languages (such as Visual J++, Visual C++, Visual Basic) using the spirit.ocx. Also the RCX ControlCenter with NQC is pretty good. (The legOS would be the ultimate thing, but it's more (...) (27 years ago, 5-Oct-99, to lugnet.robotics)
|