 | | Re: On the Subject of Treads
|
|
Hi John - - I've been using a tracked LEGO 'bot since November as a sensor test-bed without any difficulty (and with out rebuilding the track system) on an almost daily basis. See the Mindstorms Constructopedia pg. 39 for a basic idea. The axles DO (...) (27 years ago, 30-Aug-99, to lugnet.robotics)
|
| |
 | | Re: On the Subject of Treads
|
|
In lugnet.robotics, lego-robotics@crynwr.com (John Barnes) writes: [snip] (...) I have indeed seen this before, on at least three different LEGO Technic (including one RIS) kits. Its a flaw in the treads, not anything that you are doing wrong. I (...) (27 years ago, 30-Aug-99, to lugnet.robotics)
|
| |
 | | MINDSTORMS links
|
|
Hi all, The Online Resources from my upcoming book are now online. There are links and short descriptions of each resource--everything from the official MINDSTORMS site to the patent for the electrical bricks to legOS to Mouser. It's organized by (...) (27 years ago, 30-Aug-99, to lugnet.robotics)
|
| |
 | | Re: robotic rovers
|
|
(...) To which you wrote: (...) Then he wrote: (much more concisely) (...) It could work in theory, but I just tested it again with 2 motors that were grossly mismatched. Having both motors interconnected (electrically) did NOT cause their (...) (27 years ago, 30-Aug-99, to lugnet.robotics)
|
| |
 | | Re: robotic rovers
|
|
It sounds like you guys are trying to re-invent the adder/subtractor system. Check out (URL) for some designs using this. In an adder/subtractor you have two motors, A and B. The wheels are then run through a mechanical linkage such that one wheel (...) (27 years ago, 31-Aug-99, to lugnet.robotics)
|
| |
 | | Re: mechanical clutches
|
|
I agree that the adder/subtractor is the way to go (at least for now) if you want any semblance of accuracy in your robots - I even started the thread on what was the best design for the a/s (remember LDraw?) from which this branched out. (I hope (...) (27 years ago, 31-Aug-99, to lugnet.robotics)
|
| |
 | | Re: Poor man's Tachometer
|
|
(...) Would sandwiching a rubber band in place of the 1/2 height rings give you enough spacing? A single white band could probably be wrapped around both of the cross-axles, and it would keep the Lego-purists happy. I like your design--it's the most (...) (27 years ago, 31-Aug-99, to lugnet.robotics)
|
| |
 | | Sound
|
|
I wanted to make the RCX make a certain pitched sound based on sensor readings the other day (primarily the light sensor), however it appears you can't make the frequency of the command equal to a variable. Does anyone know why this is and if there (...) (27 years ago, 31-Aug-99, to lugnet.robotics)
|
| |
 | | Re: Poor man's rotation sensor (?)
|
|
(...) There two main differences between a Tachometer and a Rotation sensor 1. Tachometers count distance and do not tell you the direction the axle is rotating. 2. Tachometers must be pre-reset to zero and the angle can only the deduced after that: (...) (27 years ago, 31-Aug-99, to lugnet.robotics)
|
| |
 | | Re: [Rumour] FBI and Mindstorms
|
|
(...) i don't know if the Furby in the USA is different from those in europe, but mine can't record anything, it's nearly deaf - you have to clap very loud so that it can "hear" you - and then it follows a pre- programmed behaviour and doesn't (...) (27 years ago, 31-Aug-99, to lugnet.robotics)
|