 | | Re: Touch Sensor as a Switch
|
|
(...) Connecting N touch sensors in parallel requires N pieces of wire, while doing so in series requires N+1 pieces of wire. See? It's not that bad. Here is my experimenting results of connecting the three Cyber Master touch sensors to RCX in (...) (27 years ago, 27-Aug-99, to lugnet.robotics)
|
| |
 | | motor speed control
|
|
I have added another web page, this time discussing a way to control the speed of a motor that actually gives you a wide range of speeds. (URL) are no pictures and I had to re-type the NQC code by hand, but the method works fine; I tried it last (...) (27 years ago, 27-Aug-99, to lugnet.robotics)
|
| |
 | | Re: MacNQC for 64k Macs
|
|
I should add a link to the docs from the MacNQC page - sorry. The general NQC 2.0 beta test page has some documentation as well as a MPW tool version of NQC that should run on 68k macs: (URL) docs are very brief - mostly just a list of differences (...) (27 years ago, 27-Aug-99, to lugnet.robotics)
|
| |
 | | Re: ideas for a RIS 2.0 - Rechargability
|
|
I tried NiMH batteries in my RCX. It lost its firmware. I suspect the output voltage (6 x 1.2 = 7.2) is too low. You should be able to do it using an external battery pack, but I suggest you use 8 cells instead of 6. The resulting 9.6 volts shouln't (...) (27 years ago, 28-Aug-99, to lugnet.robotics)
|
| |
 | | Re: MacNQC for 64k Macs
|
|
Ralf, I am running the NQC tool (via MPW) on a 8MB SE/30. I'm using System 7.1 with MPW 3.4.1 (from ETO 20). It works, although things are pretty squeezed into ram. Ray Sanders rsanders@gate.net (...) (27 years ago, 28-Aug-99, to lugnet.robotics)
|
| |
 | | RE: My Multiple Posts
|
|
To All I dont know why it sent my mail multiple times, I appear to be experiencing server error. In any event, I apologize, I only meant to send it once. -Andy RIT -- Did you check the web site first?: (URL) (27 years ago, 28-Aug-99, to lugnet.robotics)
|
| |
 | | Software builds LEGO structures..
|
|
(URL) don't know if this has been posted to the list, but I thought it might be of intrest.. Looks like all us bot builders could be out of a job soon.. :-P "Evolution, until now the unchallenged domain of living organisms, may soon become possible (...) (27 years ago, 25-Aug-99, to lugnet.robotics)
|
| |
 | | Re: Climbing robot?
|
|
(...) Well, my initial thought is that a simple climber is one that has an inchworm-style motion - open upper gripper, extend the upper half, close upper gripper, release lower gripper, contract body to raise lower gripper, close lower gripper, (...) (27 years ago, 25-Aug-99, to lugnet.robotics)
|
| |
 | | Re: touch sensors aren't just switches (was Re: ideas for a RIS 2.0
|
|
Any motion between two hard surfaces, including sliding metal on metal (often called contact wiping), creates intermittent contact that has to be "debounced". The only switches that don't bounce are mercury-wetted contacts, such as one used to find (...) (27 years ago, 25-Aug-99, to lugnet.robotics)
|
| |
 | | Robots Design LEGO Structures All By Themselves
|
|
Evolution, until now the unchallenged domain of living organisms, may soon become possible for robots as well. So say computer scientists at Brandeis University, where a simple computer-based form of evolution -- nature's own design strategy -- has (...) (27 years ago, 26-Aug-99, to lugnet.robotics)
|