To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / 6516 (+10)
  RE: Base Plates
 
The grey base plate is set number "628 Extra large gray baseplate". I don't have one in front of me, but I believe it's 48x48 studs or something like that. 627 and 626 are smaller ones (maybe 32x32) in green and blue. They are in the Lego catalog at (...) (27 years ago, 24-Aug-99, to lugnet.robotics)
 
  Re: Base Plates
 
(...) The largest one I've seen for sale in the last year is a 48x48 gray baseplate for US $9.99 (at Toys R Us and The Construction Site). It's item number 628 "Extra Large Gray Baseplate" in the Shop At Home catalog (if you're using the web (...) (27 years ago, 24-Aug-99, to lugnet.robotics)
 
  Great RCX sensor page
 
While surfing yesterday I stumbled onto Michael Nielsen's web page. It has some great info about implementing RCX sensors. I don't recall ever seeing reference to Michael's page on this list ... so I requested (and received) his permission to post (...) (27 years ago, 24-Aug-99, to lugnet.robotics)
 
  Re: Base Plates
 
Robert Munafo writes: > Perhaps when you said "15x15" you were giving the dimensions in inches. The > 48x48 baseplate is 15 inches (or 38.3 centimeters) on each side. Inches are English measurements. Centimeters are Metric measurements. Studs are (...) (27 years ago, 24-Aug-99, to lugnet.robotics)
 
  RE: Base Plates
 
I appologize for the confusion. I should have been more specific. -----Original Message----- From: Robert Munafo [mailto:munafo@gccte...O.SPAMcom] Sent: Tuesday, August 24, 1999 10:18 AM To: lego-robotics@crynwr.com Subject: Re: Base Plates (...) (...) (27 years ago, 24-Aug-99, to lugnet.robotics)
 
  Re: ideas for a RIS 2.0
 
(...) If that were true, then the following multi-touch-sensor adapters would not work: (2 URLs) Robert Munafo (URL) LEGO: TC+++(8480) SW++ #+ S-- LS++ Hsp M+ A@ LM++ YB64m IC13 (27 years ago, 24-Aug-99, to lugnet.robotics)
 
  Obj.: r/c servos
 
To add more to all those servo information, I've build a servo controller which use the printer connector on the PC. It doesn't use any electronic, everything is made by software (Delphi 3.0) It is quite usefull to try this at home since you'll (...) (27 years ago, 23-Aug-99, to lugnet.robotics)
 
  Re: ideas for a RIS 2.0
 
(...) gradually depress the sensor. There is not a sharp cutoff like there is with a typical contact switch. I tried building a touch sensor multiplexor, but I was unable to reliably get even 3 to work because the minimum resistance is quite large (...) (27 years ago, 24-Aug-99, to lugnet.robotics)
 
  RE: ideas for a RIS 2.0
 
(...) But it IS true, and that's why the 6 input mux at: (URL) has some problems. Find out for yourself by putting a meter across a touch sensor. The resistance changes from about 1K to 470R when pressed depending on how hard it is pressed. Michael (...) (27 years ago, 24-Aug-99, to lugnet.robotics)
 
  Macintosh IR cable
 
Hello, I just talked to Pitsco LEGO DACTA. I was curious about the IR tower they sell, because it comes with a Macintosh cable. It turns out that the cable is available separately, item 4119830, for $15. This item is not listed in the catalog (...) (27 years ago, 24-Aug-99, to lugnet.robotics)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR