To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / 6241 (+10)
  Re: Anybody used Robolab? (RE: my $1300 grant)
 
I think it does a good job of showing the different levels of the software and how to use the software. If ou are looking for projects then it is pretty slim on projects. Jim Clark (...) This message was sent from Bess.Net, a filtered Internet (...) (27 years ago, 11-Aug-99, to lugnet.robotics)
 
  ***Anyone from N.Y.?***
 
Hi I live on long Island and am looking for people to get a possible club together or even just someone to work on robotics with. If there are any new yorkers out there please respond ! Thanks -Michael -- Did you check the web site first?: (URL) (27 years ago, 11-Aug-99, to lugnet.robotics)
 
  Re: Anybody used Robolab? (RE: my $1300 grant)
 
(...) I guess I do. If you're referring to the Getting Started - Teacher's Guide for ROBOLAB Software manual(#2000052), it certainly has lots of useful information. Much more than you will find in the paper that accompanies the RCX software. And (...) (27 years ago, 11-Aug-99, to lugnet.robotics)
 
  Re: Pnuematics: e-switch and thoughts
 
(...) the link's moved here (URL) c s soh cssoh@singnet.com.sg (URL) air is power (27 years ago, 11-Aug-99, to lugnet.build, lugnet.robotics)
 
  Re: Wireless data/control transmission
 
Yes, I've wondered about that also. The 802.11 chip set (Harris PRISM) might be an interesting choice, although increasing the H8 data rate from 2400b to 1Mb could be a small problem. With the PRISM chip set, you could get somewhere between 100 and (...) (27 years ago, 11-Aug-99, to lugnet.robotics)
 
  Re: Lazy Tongs
 
(...) Yeah, that was the first one I built. It works, but not well. I think it was my design. The "piston" kept moving left and right off the track. I'm rebuilding it now with an experimental design. I may have to bite the bullet and use it. I'm (...) (27 years ago, 11-Aug-99, to lugnet.robotics)
 
  Re: Pnuematics: e-switch and thoughts
 
(...) Linc also seems to have a new (to me, anyway) pneumatic excavator at (URL) that's really awesome! The bucket was my very first part in LDraw, BTW. I could probably do better now that I'm more experienced, but I'm afraid it will be too much (...) (27 years ago, 11-Aug-99, to lugnet.build, lugnet.robotics)
 
  Re: ***Anyone from N.Y.?***
 
(...) (27 years ago, 11-Aug-99, to lugnet.robotics)
 
  Re: Pnuematics: e-switch and thoughts
 
(...) And in message (URL) Soh Chio Siong writes: (...) here anymore. By the way, I also found another design that puts a z8 gear on the micromotor meshed with a z40 gear, then uses a 1x5 half beam to link one of the 4 center holes on the z40 gear (...) (27 years ago, 11-Aug-99, to lugnet.build, lugnet.robotics)
 
  RE: putting liquid into pneumatic elements (was Re: Darn those definitions (was: The new Super Car)
 
My first Technic set was the Yellow JCB earth mover. After taking it apart to build my own model ( a claw and arm I think). I got water in the cylinders by accident. Shortly after that the seal on the inside failed and they became useless. I advise (...) (27 years ago, 11-Aug-99, to lugnet.robotics)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR