 | | Re: I/o's expansions for the mindstorm ?
|
|
(...) This might not be relevant for everyone out there, but I thought I'd point out: If you use a learning remote to learn the codes from the MindStorms remote control, please note that all combinations of the three motor controls send out a (...) (27 years ago, 10-Aug-99, to lugnet.robotics)
|
| |
 | | Re: new products (Remote Control)
|
|
(...) 1 Send message "1" 2 Send message "2" 3 Send message "3" A^ Run motor A in > direction (see notes below) Av Run motor A in < direction (see notes below) B^ Run motor B in > direction (see notes below) Bv Run motor B in < direction (see notes (...) (27 years ago, 10-Aug-99, to lugnet.robotics)
|
| |
 | | Re: Pnuematics: e-switch and thoughts
|
|
(...) If you use a t-connector to connect each side of the circuit to a compressor (that uses a SMALL pump and NO tank!) you can maintain high pressure, and the fact that the pump's cylinder is small compared to the other two cylinders means that (...) (27 years ago, 10-Aug-99, to lugnet.build, lugnet.robotics)
|
| |
 | | Re: Pnuematics: e-switch and thoughts
|
|
(...) That link doesn't work anymore. Can anyone tell us how this construction worked? (any gears? Levers? Maybe a worm gear?) I might want to use the idea in a Mindstorms design. (by the way, I really liked the soda bottle tank idea and might try (...) (27 years ago, 10-Aug-99, to lugnet.build, lugnet.robotics)
|
| |
 | | Re: new products (Remote Control)
|
|
The remote is really handy when checking your creations before you program them. I use mine all the time. Also fun to run little cars and other bots. Even used it to drive my 8448 Street Sensation about the house. Bob Fay rfay@we.mediaone.net The (...) (27 years ago, 10-Aug-99, to lugnet.robotics)
|
| |
 | | RCX Firmware storage.
|
|
After a near heartattack with my TI-89 after upgrading it's flash ROM (I think it is flash rom, Flash Somethin, (URL) I have to ask myself what exactly does the RCX have to store the Fireware. After pulling all avaible power source to my TI-89, it (...) (27 years ago, 10-Aug-99, to lugnet.robotics)
|
| |
 | | Re: NQC (Mac) and KeySpan card?
|
|
(...) Yes, but you need to know the name of the device driver, and this is usually pretty difficult to find. Serial ports use two separate drivers - one for input and one for output. Usually the names are something like this: ".xxxIn" and ".xxxOut" (...) (27 years ago, 11-Aug-99, to lugnet.robotics)
|
| |
 | | Re: RCX Firmware storage.
|
|
(...) microcontroller's on chip ROM. The other half (which gets downloaded) isn't really firmware. Its stored in SRAM that is powered from the main batteries. If you take out the batteries the firmware will be lost after a few minutes. If you want (...) (27 years ago, 11-Aug-99, to lugnet.robotics)
|
| |
 | | Anybody used Robolab? (RE: my $1300 grant)
|
|
I talked to a guy from Pitsco today and asked him if the Robolab users guide had any useful information. Of course he said it did, but does anyone else think so. Usually any paper that comes with software is useless. Karen. (27 years ago, 11-Aug-99, to lugnet.robotics)
|
| |
 | | Re: new products (Remote Control)
|
|
Well, my program can't exactly do the stop and start up another program function yet, but accually can be pretty useful tho. Can be used with your keyboard or joystick. The Real-Time Controller (URL) in the download section. KGB AgEnT #4 OUT AKA (...) (27 years ago, 11-Aug-99, to lugnet.robotics)
|