 | | Re: Temperature Sensor
|
|
(...) At one time Radio Shack sold 10K thermistors but I have not checked lately. Don't remember their temperature coefficient. I do not know the Mouser source. Pardon me if this is an(*) FAQ but could you let me/us know how to contact Mouser? (...) (27 years ago, 28-Jul-99, to lugnet.robotics)
|
| |
 | | Re: odometry (was Re: Homing with the IR Tower)
|
|
(...) I see your point. Yes, F1 kind wheels are far from ideal to avoid slippage and get accurate results. The larger but thinner spoked wheels that come with the Minstorm RIS are quite better. The free wheel(s) also must be light and thin and (...) (27 years ago, 28-Jul-99, to lugnet.robotics)
|
| |
 | | Re: odometry (was Re: Homing with the IR Tower)
|
|
(...) Great source. Just found a source where Johann Borenstein discusses the original 1966 paper and gives links for the full electronic version or a CDROM or a book version. Here is the source: (URL) for the pointer! Ralph M. Deal deal@kzoo.edu -- (...) (27 years ago, 28-Jul-99, to lugnet.robotics)
|
| |
 | | Re: Temperature Sensor
|
|
Ralph M. Deal <lego-robotics@crynwr.com> wrote in message news:Pine.GSO.4.05.9...zoo.edu... (...) Radio Shack still sells the 10K thermistor. Mouser is at www.mouser.com The part is at the following url: (URL) description of the part is on the (...) (27 years ago, 28-Jul-99, to lugnet.robotics)
|
| |
 | | Re: Temperature Sensor
|
|
Mike, You are the man. Thanks for the information. Digi-Key sells two thermistors that match that description. The first is KC003T-ND, for $2.71; it has 1 degree accuracy. The second is KC003A-ND, for $11.50; it has +- .2 degree accuracy. I tried (...) (27 years ago, 28-Jul-99, to lugnet.robotics)
|
| |
 | | Re: pneumatics & mindstorms?
|
|
(...) Well, ultimately the pneumatic power comes from the motor that drives the compresser. At a given time frame you can only squeeze so much work out of the motor, and pneumatics is no magic. It gives you great power but still not much speed, if (...) (27 years ago, 28-Jul-99, to lugnet.robotics, lugnet.build)
|
| |
 | | Broken links (was Re: pneumatics & mindstorms?)
|
|
I can't get these links to work now. Can anyone find the image and post a new link to it? Maybe someone who actually downloaded it as Tim suggested? (...) (27 years ago, 28-Jul-99, to lugnet.robotics, lugnet.build)
|
| |
 | | Re: pneumatics & mindstorms?
|
|
(...) After the big piston operates once, how long does it take to recharge the pressure? (...) I did not build a compressor using the large pumps before, only the small pumps, so I believe in your findings. Still I wonder why. The larger pump takes (...) (27 years ago, 28-Jul-99, to lugnet.robotics)
|
| |
 | | Re: pneumatics & mindstorms?
|
|
(...) (extra removed) (...) Don't forget, at the actuation end, a pneumatic-based motor should be liquid compatible, something the electric motors have a hard time with. Also, you can run the air lines quite far, so long as you are willing to accept (...) (27 years ago, 28-Jul-99, to lugnet.robotics)
|
| |
 | | Re: Temperature Sensor
|
|
Jonathan Knudsen <lego-robotics@crynwr.com> wrote in message news:3.0.5.32.199907...net.com... (...) You might try a trim pot in place of the 2.2K and set the room temperature to be the correct value. You could later determine the trim pot value (...) (27 years ago, 28-Jul-99, to lugnet.robotics)
|