To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / 531 (+20)
  Re: Homebrew sensors?
 
(...) I was thinking of something that sensed amplitude, not frequency. (Like the light sensor, which sees brightness, not color.) Of course, whatever you want for yourself is best. :) I know the logic of taking two sensors and differentiating to (...) (28 years ago, 14-Nov-98, to lugnet.robotics)
 
  Re: Homebrew sensors?
 
(...) Unfortunately the bang comes with the whoosh, often leading to a rapid unplanned dissasembly. Witness the recent destruction of Delta III #1, caused by a 4hz roll oscillation, or the Titan IV that ended in a BFRC due to a clog in its wacky (...) (28 years ago, 14-Nov-98, to lugnet.robotics)
 
  RE: Homebrew sensors?
 
Why would you need an array to do that? You could do it with three variables: var1 = starting angle var2 = highest amplitude encountered so far var3 = angle of highest amplitude The algorithm goes something like this (in pseudo-C): var1 = (...) (28 years ago, 14-Nov-98, to lugnet.robotics)
 
  MindStorms on NT / trouble posting to the list
 
I'm posting this question on behalf of peterbag@microsoft.com. Please direct replies to that address... Peter asks, Help! I am considering purchasing a MindStorms kit tonight, but I want to make sure it will run under WindowsNT. Has anyone done (...) (28 years ago, 14-Nov-98, to lugnet.robotics)
 
  Re: moving in a straight line with two motors?
 
Alex Wetmore wrote in message <008601be0f2a$01b821...ft.com>... (...) This would give you a good turning radius. However, it would take the bot a long time to turn. (...) (28 years ago, 14-Nov-98, to lugnet.robotics)
 
  Re: moving in a straight line with two motors?
 
Ardjan Besse wrote in message <364c7d42.4532817@lu...et.com>... (...) "Straight" is a relative term. For example, while the alignment might be 0straight, the wheels might not provide the bot with the ability to travel in a straight line. I believe (...) (28 years ago, 14-Nov-98, to lugnet.robotics)
 
  Re: moving in a straight line with two motors?
 
(...) 1) You've been playing too much Carmageddon. 2) Control theory is relatively new (it paces the development of computers). There are quite a few good textbooks available, but a professor is a much greater help. Familiarity with calculus and (...) (28 years ago, 14-Nov-98, to lugnet.robotics)
 
  Re: moving in a straight line with two motors?
 
Daniel Miller wrote in message ... (...) What? (...) This is all fine and well, but I was thinking about something a little less complex. The RCX doesn't have the power to perform image processing and sophisticated feedback control. What I was (...) (28 years ago, 14-Nov-98, to lugnet.robotics)
 
  Cybermaster protocol?
 
Does anybody have information on the basic Cybermaster packet protocol handy? How does it differ from the 55 ff 00 D ~D D ~D C ~C format of the RCX? -Kekoa (28 years ago, 14-Nov-98, to lugnet.robotics)
 
  Re: moving in a straight line with two motors?
 
(...) Believe it or not, I've been working on exactly this problem for the last few days. I built an angle sensor using a 500K potentiometer wired directly to an RCX input port. (Lego's angle sensor doesn't have sufficient angular resolution unless (...) (28 years ago, 14-Nov-98, to lugnet.robotics)
 
  Re: Homebrew sensors?
 
(...) So's Michael - he's proposing a notch filter so you get the amplitude at a particular frequency, which may be better for a seeking application. Cheers, Ben. (28 years ago, 14-Nov-98, to lugnet.robotics)
 
  Re: moving in a straight line with two motors?
 
(...) I think making the pendulum longer should cure this... (...) Possibly making it heavier will cure this... Cheers, Ben. (28 years ago, 14-Nov-98, to lugnet.robotics)
 
  Re: Homebrew sensors?
 
In article <Pine.GSO.3.96.98111...129.6050E- 100000@expert.cc.purdue.edu>, Daniel Miller <danielmi@expert.cc.purdue.e du> writes (...) Ah. A jet engine expert. It always puzzled me how the hot air knows it is supposed to go out of the hole at the (...) (28 years ago, 14-Nov-98, to lugnet.robotics)
 
  Re: Homebrew sensors?
 
does pressure difference make any sense?..:-) Selçuk (...) (28 years ago, 14-Nov-98, to lugnet.robotics)
 
  Re: moving in a straight line with two motors?
 
---...--- (...) attached. (...) is (...) is (...) sheet (...) I expect that the "motor is shorted" state is achieved by turning on either both high-side drive FET's or both low-side drive FET's, and niether of these combinations would provide a high (...) (28 years ago, 14-Nov-98, to lugnet.robotics)
 
  Re: Cybermaster protocol?
 
(...) If I'm not mistaken, Peter Ljungstrand has compiled this information at (URL) (28 years ago, 14-Nov-98, to lugnet.robotics)
 
  Mindstorms meeting in Boston
 
Hey -- any Boston area people should come to the Construction Site tomorrow (Nov 15) from 7-9 for a Mindstorms show-n-tell/get-together. Details (such as there are) on lugnet in lugnet.loc.us.ma.bos (28 years ago, 14-Nov-98, to lugnet.robotics)
 
  How to receive messages from the CuberMaster unit?
 
I'm currently using Dave Baum's NQC on a Linux system with CyberMaster (thanks to Peter Ljungstrand's adaption), and am very happy with that. However, I often find myself in the position where I want to transfer data from the CyberMaster mobile unit (...) (28 years ago, 14-Nov-98, to lugnet.robotics)
 
  Re: moving in a straight line with two motors?
 
(...) Image processing? Proportional control pushes back proportional to deflection (i.e. it simulates a spring). Derivative control pushes back proportional to rate of deflection (i.e. it simulates dynamic friction). Integral control pushes back (...) (28 years ago, 14-Nov-98, to lugnet.robotics)
 
  Re: moving in a straight line with two motors?
 
(...) Perhaps you're asking too much of them. Try toning down the pendulum; that is, give it some length below the hinge point as well. As long as it's still top-heavy you're still technically an inverted pendulum, and the added mass below the pivot (...) (28 years ago, 14-Nov-98, to lugnet.robotics)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR