 | | Re: rotation sensor question
|
|
(...) There is very little turning resistance, but then this isn't a ball-bearing shaft with lubrication. It is probably as little as you can expect from a Lego part. John A. Tamplin Traveller Information Services jat@LiveOnTheNet.COM 2104 West (...) (27 years ago, 28-May-99, to lugnet.robotics)
|
| |
 | | rotation sensor question
|
|
A quick question for those of you that have rotation sensors- do they spin freely, or would they add significant friction to a setup? I ask because I'd like to experiment with a balancing problem, and would need to measure the angle of a pole (...) (27 years ago, 28-May-99, to lugnet.robotics)
|
| |
 | | Re: Servo controlers for mindstorms?
|
|
(...) Do you mean a piece of hardware or a piece of software? I do not know of any hardware to convert from the Mindstorms output ports to the servo inputs, so if you desire to do this sort of thing you will presumably have to get cozy with a (...) (27 years ago, 28-May-99, to lugnet.robotics)
|
| |
 | | Re: Sending raw IR characters.
|
|
(...) The problem is that you can't simply use a terminal program to communicate with the RCX. The IR interface doesn't allow the transmission of arbitrary patterns of bytes and therefore won't allow it. You need to encode bytes before sending them, (...) (27 years ago, 28-May-99, to lugnet.robotics)
|
| |
 | | Servo controlers for mindstorms?
|
|
Does any one know of some kind of "adapter" to get servos to work with the mindstorms set? (27 years ago, 28-May-99, to lugnet.robotics)
|
| |
 | | Re: Pneumatic power
|
|
(...) IMHO Ralph Hempel have some of the best pneumatic tools (switch and compressor) seen on the net at his site: (URL) working myself at a bigger compressor for a *LARGE* pneumatic project, but I'm not yet ready Mario ---...--- Mario Ferrari (...) (27 years ago, 28-May-99, to lugnet.robotics)
|
| |
 | | Sending raw IR characters.
|
|
Hi, I'm fairly new to all these things with the Lego Minstorm (i.e. I only picked one up last Tuesday.), so this might be a fairly stupid question, but I've been unable to find an answer. I've been using the LegOS distirbution running under gcc on a (...) (27 years ago, 28-May-99, to lugnet.robotics)
|
| |
 | | RE: Floating point support for 1142 bytes
|
|
(...) Let's face it Kekoa, you just couldn't stand not REALLY knowing what the group was talking about so you went and did the work we should have done before the discussion even started. :-) (...) (URL) That's a bit easier to deal with. Way to go. (...) (27 years ago, 28-May-99, to lugnet.robotics, lugnet.robotics.rcx)
|
| |
 | | Floating point support for 1142 bytes
|
|
Following some discussion about the topic a few weeks ago, I was sufficiently curious and motivated enough to write a floating point library for the H8/RCX. Initially I thought I'd implement a non-IEEE floating point format optimized for the RCX, (...) (27 years ago, 27-May-99, to lugnet.robotics, lugnet.robotics.rcx)
|
| |
 | | Pneumatic power
|
|
I am looking for some sites that revolve around Pneumatics. I need some ideas on how to do work on some switchs and make a decent compressor. KGB AgEnT #4 OUT -- Did you check the web site first?: (URL) (27 years ago, 27-May-99, to lugnet.robotics)
|