To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / 4521 (+10)
  Re: Steering a robot
 
(...) I have two designs that use separate steering and propulsion motors: (URL) (28 years ago, 12-Apr-99, to lugnet.robotics)
 
  Re: **lego motors?**
 
Use the "differtrans." See (URL) OR AT (URL) M. Tonkens, M.D. Medical Director Primary Care of Nevada 100 North Green Valley Parkway Suite 240 Henderson, NV 89014 702 914-7120 VOICE 702 914-7129 FAX BMajik5127@aol.com (...) RMT -- Did you check the (...) (28 years ago, 12-Apr-99, to lugnet.robotics)
 
  Re: Steering a robot
 
Thanks to everyone that responded. I do indeed have a differential setup on the rear wheels and a second differential to incorporate the power of two motors. The steering problem is that I don't know how to reset the steering wheels on the front of (...) (28 years ago, 12-Apr-99, to lugnet.robotics)
 
  Re: Steering a robot
 
(...) On one of my robots I have a light sensor that I use the third motor to scan to the left and right. I use a single touch sensor and two cams such that it knows when it has reached either extreme. Using the Fwd(), Rev(), and Off() routines will (...) (28 years ago, 12-Apr-99, to lugnet.robotics)
 
  Web site update
 
I have up dated my site with my Senior project that I built out of my lego mind stormes. Check it out (URL) on the senior project link Download Neoplanet at (URL) you check the web site first?: (URL) (28 years ago, 13-Apr-99, to lugnet.robotics)
 
  Re: Steering a robot
 
(...) This is a good starting point for a gear system that uses one motor to drive both wheels, and another that adds and subtracts rotations from the wheels to produce turning. (URL) subject has been covered a lot in earlier messages, so it may be (...) (28 years ago, 12-Apr-99, to lugnet.robotics)
 
  wall-follower using Dennis Clark's IRPD
 
Earlier this year I tried building a wall-follower using RCX's built-in IR port as the proximity detector. However I could not get consistent readings from the light sensor to make it work. I thought it was because the SendMessage trick did not turn (...) (28 years ago, 12-Apr-99, to lugnet.robotics)
 
  clutch gear
 
Is the motor kit the only way to get a clutch gear? Joel Shafer joel@connect.net -- Did you check the web site first?: (URL) (28 years ago, 12-Apr-99, to lugnet.robotics)
 
  Re: clutch gear
 
(...) No, but it's probably the cheapest, unless it's in a Dacta spare parts kit I don't know about. Target had the 3735s on sale for over 50% off. It's also in the 8479 Bar Code Multi set, but that's $160. These are the only two sets that have it (...) (28 years ago, 13-Apr-99, to lugnet.robotics)
 
  Dark seeker project
 
I have finally built a creation with my Mindstorms kit that uses all of the sensors (some twice) and all of the motor connections! It has two bump switches for a collision detector on the front, one of my RCX IRPD modules to try to detect potential (...) (28 years ago, 13-Apr-99, to lugnet.robotics)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR