To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / 4351 (+10)
  Re: multi-device output controller
 
(...) And where are you getting motor drive power from? I assume you want the selected motor to run at full power, not at 1/8, 1/4, etc. I'm afraid you're still stuck consuming the extra output for power unless you use a separate power source. (28 years ago, 26-Mar-99, to lugnet.robotics)
 
  Re: multi-device output controller
 
(...) With a seperate battery box (from 8735 for instance) you could power the output full time. In this case you'd probably want to map it to something like this: off - off 1 - output 1 fwd 2 - output 1 rev 3 - output 2 fwd 4 - output 2 rev 5 - (...) (28 years ago, 26-Mar-99, to lugnet.robotics)
 
  Re: multi-device output controller (fwd)
 
----- Forwarded message from Bill Flanagan ----- From: "Bill Flanagan" <bflanagan@mediaone.net> Subject: Re: multi-device output controller (fwd) Date: Fri, 26 Mar 1999 11:26:31 -0500 How about an RCX to RS232 connection to use off the shelf (...) (28 years ago, 26-Mar-99, to lugnet.robotics)
 
  Re: multi-device output controller (fwd)
 
Hi Bill, ----- Forwarded message from Bill Flanagan ----- From: "Bill Flanagan" <bflanagan@mediaone.net> Subject: Re: multi-device output controller (fwd) Date: Fri, 26 Mar 1999 11:26:31 -0500 I like the ide that you have but like you, I am not a (...) (28 years ago, 26-Mar-99, to lugnet.robotics)
 
  Re: multi-device output controller (fwd)
 
----- Forwarded message from Jim Choate ----- From: Jim Choate <ravage@ssz.com> Subject: Re: multi-device output controller (fwd) Date: Fri, 26 Mar 1999 10:34:22 -0600 (CST) It's actualy pretty easy. Take the analog RCX output, integrate, S&H, A/D, (...) (28 years ago, 26-Mar-99, to lugnet.robotics)
 
  Re: multi-device output controller (fwd)
 
Has anyone tried out the Muscle Wire or electronic pistons from this site? Seems like a good alternative to pneumatics. (...) -- Did you check the web site first?: (URL) (28 years ago, 26-Mar-99, to lugnet.robotics)
 
  Re: multi-device output controller (fwd)
 
Cool. You can also add things like the following: 1. Serial LCD display 2. GPS devices 3. additional infrared send/recieve 4. ANY PC project that is serial port connected! I like the idea of multiple serial channels; this means that you can talk to (...) (28 years ago, 26-Mar-99, to lugnet.robotics)
 
  Re: multi-device output controller
 
(...) There are 8 levels of PWM, so fwd/rev for 4 devices is possible. I originally wanted a separate power input to allow a full 8 levels for each device. This would allow the controller to operate ANY device designed for the RCX ports and not (...) (28 years ago, 26-Mar-99, to lugnet.robotics)
 
  Re: multi-device output controller
 
There is no need to waste PWM levels on reverse. You can set the RCX motor output to reverse speeds as well, giving you 7 outputs (fwd and rvs) instead of 3 1/2. You need a bridge rectifier anyway; you might as well exploit it to indicate direction. (...) (28 years ago, 26-Mar-99, to lugnet.robotics)
 
  Muscle wire and alternatives
 
----- Forwarded message from Joel Shafer ----- Date: Fri, 26 Mar 1999 11:12:57 -0600 From: Joel Shafer <joel@connect.net> Subject: Re: multi-device output controller (fwd) Has anyone tried out the Muscle Wire or electronic pistons from this site? (...) (28 years ago, 26-Mar-99, to lugnet.robotics)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR